View Profile: gringeltaube - Steel Soldiers::Military Vehicles Supersite

02-11-2019, 19:57

gringeltaube replied to a thread Brake Not Bleeding off Pressure in The Deuce

Before anything else - read this post... Your issue might be as simple as a MC-pushrod adjusted too long!? (thanks to ecbarnum for his very...

16 replies | 305 view(s)

02-03-2019, 09:44

gringeltaube replied to a thread M1009 value question. in CUCV

Please remember this is not the place to post any want-to-buy/sell/trade info.

29 replies | 570 view(s)

01-29-2019, 23:18

gringeltaube replied to a thread M1009 value question. in CUCV

You may get 6k for it, or even more... depending on how much someone else wants it. Although, I don't think anyone would consider an M1009 a...

29 replies | 570 view(s)

01-29-2019, 11:00

gringeltaube replied to a thread Looking for aTool Outfit, Hydraulic Test and Repair, Trailer in Vehicles wanted

Once you have that new thread up - and as long as this one still goes on - I can probably move over some of what was posted here. It is a pity...

17 replies | 360 view(s)

01-27-2019, 09:29

gringeltaube replied to a thread Need to move a M35a2 from Somerset to Pittsburgh 100miles in Transportation Needs

I would try USF, here... even if it is only a short distance. (See this thread, for reference.)

9 replies | 277 view(s)

01-27-2019, 08:49

gringeltaube replied to a thread need a shipping company in Transportation Needs

Check out this thread...

9 replies | 289 view(s)

01-23-2019, 22:27

gringeltaube replied to a thread has anyone taken injectors apart on this forum? in CUCV

I think they are just press-fitted, not screwed-in. I have never had one come loose; not even after slightly bending them (accidentally).

25 replies | 531 view(s)

01-23-2019, 08:25

gringeltaube replied to a thread hemtt shafts problem in 5-ton and up

That's correct (for your M983).

25 replies | 556 view(s)

01-22-2019, 18:51

gringeltaube replied to a thread hemtt shafts problem in 5-ton and up

ha-ha... I agree!

25 replies | 556 view(s)

01-22-2019, 18:49

gringeltaube replied to a thread hemtt shafts problem in 5-ton and up

You need to pay more attention to the UOC listings... (UOC stands for "Usable-On-Code", with the different codes explained in the introduction, page...

25 replies | 556 view(s)

01-22-2019, 10:55

gringeltaube replied to a thread Flywheel clutch info needed in CUCV Hot Rodding and Modification

I have always used them in-distinctively, on either engine. Balancing counterweight and relative placement is exactly the same.

10 replies | 181 view(s)

01-21-2019, 09:06

gringeltaube replied to a thread New member from Spain! in Requirements For New Members

For now, the CUCV Forum would be the right section to post pics and description of your M1009. But with all those planned modifications/upgrades, the...

18 replies | 204 view(s)

01-20-2019, 22:09

gringeltaube replied to a thread M35a2 6x6 in The Deuce

Of course, you can try the flushing method first, if that means less work (and cost) for you. But in order to pull the front output section you...

38 replies | 637 view(s)

01-20-2019, 14:29

gringeltaube replied to a thread Need help from the experts. M35A2 Winch in The Deuce

All that, for $50??? No, you didn't win it... , you stole it!:) Grade-5 hardware will work and Grade-8 is perfect... Anyway, be prepared to...

13 replies | 301 view(s)

01-20-2019, 14:03

gringeltaube replied to a thread M35a2 6x6 in The Deuce

If so, then why not just pull the front output section off of the T-case? Then, disassembling it and inspecting these sprag clutches is no big deal...

38 replies | 637 view(s)

gringeltaube
Moderator

Mini Statistics

Basic Information

About gringeltaube

Statistics

Total Posts

Total Thanks

General Information

gringeltaube Moderator

Mini Statistics

Basic Information

About gringeltaube

Statistics

Total Posts

Total Thanks

General Information

gringeltaube
Moderator