Tab Content
  • NDT's Avatar
    Yesterday, 01:07
    NDT replied to a thread 1953 M37 vin in M37
    On the hardly readable data plate.
    3 replies | 80 view(s)
  • NDT's Avatar
    06-13-2019, 12:43
    Transmission is not in any way connected to air system. If you are applying brake to shift to reverse, maybe this is what is making you believe the...
    4 replies | 80 view(s)
  • NDT's Avatar
    06-13-2019, 00:07
    NDT replied to a thread Hobbs 901DS in Trailers
    That is worth saving. It's referred to as a 1 ton trailer, it's WWII, usually made by Ben Hur.
    1 replies | 73 view(s)
  • NDT's Avatar
    06-11-2019, 01:37
    See if a local drive shaft shop is available to re-tube yours. Cheaper usually.
    1 replies | 68 view(s)
  • NDT's Avatar
    06-10-2019, 12:08
    NDT replied to a thread Driveshafts in FMTV
    Axle pinion is parallel to frame. So there is the allowed 2 degrees.
    39 replies | 569 view(s)
  • NDT's Avatar
    06-10-2019, 10:56
    NDT replied to a thread M1079 runs hot and shuts down in FMTV
    Any chunks of plastic floating around in the cooling system will for sure end up plugging the radiator tubes, leading to overheating. Flush...
    4 replies | 133 view(s)
  • NDT's Avatar
    06-08-2019, 15:53
    NDT replied to a thread Driveshafts in FMTV
    How did you find that the factory drive shafts are unbalanced? They were removed in the field by Stewart and Stevenson employees and destroyed. The...
    39 replies | 569 view(s)
  • NDT's Avatar
    06-08-2019, 05:33
    The front brakes are not part of the parking brakes. Does the front brake release with zero air pressure in the system? That would mean air system...
    39 replies | 520 view(s)
  • NDT's Avatar
    06-07-2019, 15:34
    NDT replied to a thread M915A1 Governor Help in 5-ton and up
    There were no civilian M915A1s. 58 mph is against the governor, that is all any of them will do. Just takes a little longer to get somewhere that's...
    7 replies | 111 view(s)
  • NDT's Avatar
    06-05-2019, 16:03
    Yes, the price our country has paid for freedom is significant. Just took a similar picture myself.
    3 replies | 172 view(s)
  • NDT's Avatar
    06-02-2019, 16:24
    NDT replied to a thread Seized my engine! in The Early Deuce
    Yes the distributor drives the oil pump. Can say for nearly certain this was operator error. Is the distributor dimensionally identical? You will...
    23 replies | 783 view(s)
  • NDT's Avatar
    06-02-2019, 07:45
    NDT replied to a thread Is this a M7 or M17 in Trailers
    A 4' round hole pattern could be for quad mount. Rectangular pattern could be generator. Director would have holes to attach the house.
    5 replies | 172 view(s)
  • NDT's Avatar
    06-01-2019, 08:39
    NDT replied to a thread Is this a M7 or M17 in Trailers
    There were many uses for those such as generator or director. Hole patterns may tell the story. Likely from Holloman NM. A little overkill for a...
    5 replies | 172 view(s)
  • NDT's Avatar
    05-30-2019, 13:58
    I saw my first skysweeper AA towed gun at Leo Porter's yard in DFW years ago. He said he towed it there with one of his Chevy repower M715s. Later...
    18 replies | 547 view(s)
  • NDT's Avatar
    05-26-2019, 17:31
    NDT replied to a thread HMMWV injector pump bad or?? in HMMWV
    Whole front of the motor for an IP replace? Nope, read the manual. IP rebuild should run you around $500. If diesel don't come out the injector...
    68 replies | 4349 view(s)
  • NDT's Avatar
    05-26-2019, 17:26
    Anybody else spot the M246 tractor wrecker bed/crane mounted to the back of it? What a foolish idea to attempt to resurrect that antique for a gold...
    18 replies | 547 view(s)
  • NDT's Avatar
    05-25-2019, 11:50
    NDT replied to a thread wheels in FMTV
    Only Caiman II MRAP wheels with standard 10 hole Budd pattern.
    1 replies | 86 view(s)
  • NDT's Avatar
    05-25-2019, 09:51
    GTB trucks of all variants are rare, production numbers were around 10,000 if I recall. Sure if the bomb hoist were missing I would say make a...
    19 replies | 597 view(s)
  • NDT's Avatar
    05-21-2019, 21:16
    Don't trust your voltmeter! Mine reads zero, 22, 24, 28, 34 depending on how hard you tap on the glass. Verify with a known good vom at the power...
    13 replies | 204 view(s)
  • NDT's Avatar
    05-21-2019, 17:53
    That would be easy were it not for the 24 volt requirement of the WTEC control.
    13 replies | 204 view(s)
  • NDT's Avatar
    05-20-2019, 21:56
    NDT replied to a thread How to fix Blowby in Generators
    Could be excessive moisture in crankcase steaming out. Change oil before condemning engine.
    70 replies | 1435 view(s)
  • NDT's Avatar
    05-18-2019, 15:47
    NDT replied to a thread REO M275 truck tractor in The Deuce
    What is the number to the right of 17,000 lbs? I can't read it on your picture.
    77 replies | 1595 view(s)
No More Results
About NDT

Basic Information

About NDT
Biography:
Been involved with military vehicles and equipment since I was 15 years old.
Location:
Camp Wood/LC, TX
Interests:
Comm equipment, shelter carriers, line haul trucks, equipment transporters, engineer equipment
Occupation:
Manufacturing Engineer
MVPA:
4954

Statistics


Total Posts
Total Posts
7,128
Posts Per Day
1.86
Total Thanks
Total Thanks
2,064
General Information
Last Activity
Yesterday 04:30
Join Date
12-21-2008
Referrals
1
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
26
100.0%
Members who left positive:
Members who left negative:
26
0
Total positive feedback: 40
Submit Feedback For NDT
View Complete Feedbacks for NDT
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0