Tab Content
  • Ronmar's Avatar
    01-20-2019, 23:47
    Ronmar replied to a thread rear windows for the m1078 in FMTV
    You would want to source the rubber seal material first so that you can cut the lip to the proper dimenion to match the frame groove in the rubber...
    4 replies | 128 view(s)
  • Ronmar's Avatar
    01-19-2019, 22:14
    Yep, set the selector on the hydraulic panel to “cab lower” and pump it down past the balance point... oh, and with a stepstool, it is not too...
    3 replies | 107 view(s)
  • Ronmar's Avatar
    01-17-2019, 21:44
    Well if my math is any good, 75PSI is 136% of 55PSI. So the 20PSI sand setting X 1.36 should net you something under 27PSI? Interesting mod. Is...
    8 replies | 191 view(s)
  • Ronmar's Avatar
    01-12-2019, 22:43
    Ronmar replied to a thread Ether start in the FMTV in FMTV
    24v
    41 replies | 809 view(s)
  • Ronmar's Avatar
    01-12-2019, 21:23
    Ronmar replied to a thread CTIS and Arduino in FMTV
    Tom my switch still cycles at high RPM untill the tire pressure reaches somewhere over 65PSI. At that point the wet tank outflow to CTIS decreases...
    47 replies | 1375 view(s)
  • Ronmar's Avatar
    01-12-2019, 17:20
    Ronmar replied to a thread CTIS and Arduino in FMTV
    So you are using the wet tank pressure switches 115 PSI closed to 90 PSI open points to control the inflate timing? I thought about using that switch...
    47 replies | 1375 view(s)
  • Ronmar's Avatar
    01-11-2019, 17:26
    Ronmar replied to a thread CTIS and Arduino in FMTV
    I would be curious what safety precautions are written into the code...
    47 replies | 1375 view(s)
  • Ronmar's Avatar
    01-06-2019, 19:55
    No real update, I unfortunately have a lot of projects and I am building a house. Am typing this while taking a break from struggling to put a...
    15 replies | 726 view(s)
  • Ronmar's Avatar
    01-05-2019, 01:27
    Ronmar replied to a thread Problem with cab air ride ? in FMTV
    Well all the air from the primary and secondary tanks comes thru the wet tank so it is at least reaching the pressure registering on the pri/sec air...
    15 replies | 281 view(s)
  • Ronmar's Avatar
    01-04-2019, 20:10
    Ronmar replied to a thread Problem with cab air ride ? in FMTV
    Yep, The protection valve only lets air pass when the wet tank is above around 85PSI. There are two lines coming off of the protection valve, a...
    15 replies | 281 view(s)
  • Ronmar's Avatar
    12-31-2018, 17:19
    Ronmar replied to a thread Cab Tilt Lock Light in FMTV
    And if it was really important to you, you could wire the switch into the troop switch circuit so the sonalert would beep at you:)
    22 replies | 461 view(s)
  • Ronmar's Avatar
    12-24-2018, 19:17
    You turn the main switch on and press the start inhibit button once. This sets a latching relay(you can hear it click) and the vehicle will crank but...
    5 replies | 167 view(s)
  • Ronmar's Avatar
    12-23-2018, 19:55
    To do what you are thinking I dont think those cylinders will have enough travel to allow you to hook them up before entering rough terrain and still...
    9 replies | 694 view(s)
  • Ronmar's Avatar
    12-23-2018, 19:06
    319 summed it up, you have too many unknowns... Pressurizing cooling system, are there any contaminants in the coolant? Is there any coolant in the...
    7 replies | 276 view(s)
  • Ronmar's Avatar
    12-22-2018, 20:14
    How did you know it was the park brake? Did the park and emer brake lights illuminate in the indicator panel?
    20 replies | 614 view(s)
No More Results
About Ronmar

Basic Information

About Ronmar
Location:
Port angeles wa

Statistics


Total Posts
Total Posts
143
Posts Per Day
0.87
Total Thanks
Total Thanks
13
General Information
Last Activity
Yesterday 23:07
Join Date
08-11-2018
Referrals
0
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For Ronmar
View Complete Feedbacks for Ronmar
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0