Tab Content
  • Kemper's Avatar
    11-11-2019, 21:26
    Got mine off amazon. Seems to be pretty good quality. The only modification I made was adding spiral wrap on the cord after the heat shield to...
    32 replies | 540 view(s)
  • Kemper's Avatar
    11-07-2019, 22:19
    Kemper replied to a thread CTIS - Almost working in FMTV
    Found your original thread: https://www.steelsoldiers.com/showthread.php?181972-CTIS-and-Arduino/page7 Looks simple enough. I wonder how many...
    30 replies | 532 view(s)
  • Kemper's Avatar
    11-06-2019, 21:46
    Kemper replied to a thread CTIS - Almost working in FMTV
    Good to know. It has to be more reliable.
    30 replies | 532 view(s)
  • Kemper's Avatar
    11-06-2019, 18:44
    Kemper replied to a thread CTIS - Almost working in FMTV
    My guess is they are giving you pricing to redesign it. Iím sure itís obsolete at this point. Picked on NOS one on eBay for $500. Iíve been...
    30 replies | 532 view(s)
  • Kemper's Avatar
    11-04-2019, 20:33
    Kemper replied to a thread CTIS - Almost working in FMTV
    After all that it was the computer after all. Got a new one and it works perfectly. Inflates and deflates.
    30 replies | 532 view(s)
  • Kemper's Avatar
    11-01-2019, 20:17
    Kemper replied to a thread CTIS - Almost working in FMTV
    Ran the PCU on shop air. Still have the same fault. Solutions still on the "To Do" List - Have a new CTIS controller on the way. Will swap it in...
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-29-2019, 21:16
    Kemper replied to a thread CTIS - Almost working in FMTV
    I did not. Sounds like that is tomorrows project.
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-29-2019, 20:50
    Kemper replied to a thread CTIS - Almost working in FMTV
    Shop air 120-130psi but the wet tank pressure switch was jumped out.
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-29-2019, 20:47
    Kemper replied to a thread CTIS - Almost working in FMTV
    Each one reads just about 60 ohms.
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-29-2019, 20:36
    Kemper replied to a thread CTIS - Almost working in FMTV
    They were all a little above 60 ohms
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-29-2019, 20:10
    Kemper replied to a thread CTIS - Almost working in FMTV
    They all show the correct ohms and look clean. By check do you mean hook them to a power supply and see if they function? I was hesitant to remove...
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-29-2019, 20:04
    Kemper replied to a thread CTIS - Almost working in FMTV
    Supplier: Amazon Part: AUTEX Pressure Transducer/Sender/Sensor 150/200 Psi Stainless Steel Compatible With Oil, Fuel, Air, Water (150 Psi) ...
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-28-2019, 20:23
    Kemper replied to a thread CTIS - Almost working in FMTV
    Ordered. Thanks for the idea
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-27-2019, 19:13
    Kemper replied to a thread CTIS - Almost working in FMTV
    Ronmar thanks for the great info! Ill by-pass the PCU tomorrow as you suggested. I've come across your video before. That is my last resort if I...
    30 replies | 532 view(s)
  • Kemper's Avatar
    10-27-2019, 17:33
    Kemper started a thread CTIS - Almost working in FMTV
    UPDATE: Problem solved. Computer was bad. Replaced with a new one. Steps listed throug the post are still helpful first steps. UPDATE...
    30 replies | 532 view(s)
No More Results
About Kemper

Basic Information

Age
33
About Kemper
Location:
Centerville, NJ

Statistics


Total Posts
Total Posts
17
Posts Per Day
0.44
Total Thanks
Total Thanks
4
General Information
Last Activity
Yesterday 19:23
Join Date
10-06-2019
Referrals
0
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For Kemper
View Complete Feedbacks for Kemper
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0