View Profile: builmord - Steel Soldiers::Military Vehicles Supersite

Today, 09:38

builmord replied to a thread Another MEP-802 standby generator thread in Generators

if your system main bonding jumper, connection of grounded conductor with grounding conductor, is located in your house service panel, first means of...

17 replies | 909 view(s)

Yesterday, 20:21

builmord replied to a thread mep-802a engine oil leak in Generators

my only experience with blow by is with my unit. amazing how a nearly invisible oil mist looks like a major oil leak after a couple hours of run...

16 replies | 275 view(s)

12-03-2019, 13:48

builmord replied to a thread mep-802a engine oil leak in Generators

be careful to remove all shop rags, paper towels etc. my mistake was leaving a small rag just outside the open door to the engine compartment. ...

16 replies | 275 view(s)

12-02-2019, 12:49

builmord replied to a thread mep-802a engine oil leak in Generators

just a thought. could be blow by coming out of the dip stick hole

16 replies | 275 view(s)

11-21-2019, 09:41

builmord replied to a thread mep802a what is too much in Generators

fluids changed twice, contact cleaner and wiring harness check done, seafoam in fuel tank and associated running of unit complete, inspection of...

10 replies | 390 view(s)

11-20-2019, 13:26

builmord replied to a thread mep802a what is too much in Generators

thank you all. I am just paranoid about hurting my baby, she's my first diesel and I want to treat her right

10 replies | 390 view(s)

11-19-2019, 18:18

builmord started a thread mep802a what is too much in Generators

i read many posts of gens running way over 100% of their rated load in an attempt to cure wet stacking issues. the electrical end is protected by...

10 replies | 390 view(s)

11-17-2019, 18:16

builmord replied to a thread mep802a oil gusher in Generators

looks like I cause rather than fix problems. a slight over fill and 5w40 verses 15w40 caused blow by. I changed the oll back to 15w40 and was...

4 replies | 192 view(s)

11-17-2019, 09:57

builmord started a thread mep802a oil gusher in Generators

everything looked fine. gen ran and held a 100% load for 2 hours. so I changed the oil, used 5w40 as if is cold here in virginia. ran the engine...

4 replies | 192 view(s)

11-10-2019, 13:56

builmord replied to a thread mep8002a IP fuel rate adjustment in Generators

my comparison was based on how my 5kw honda inverter / generator ran. I know now these are two very different animals

11 replies | 280 view(s)

11-10-2019, 09:01

builmord replied to a thread mep8002a IP fuel rate adjustment in Generators

thank you all. This is my first diesel with nothing to compare it to. I guess I am just a Nervious Nelly. I best leave well enough alone

11 replies | 280 view(s)

11-08-2019, 18:39

builmord replied to a thread mep8002a IP fuel rate adjustment in Generators

thanks, took temp readings on the exhaust manifolds. only 1 or 2 degrees different. I guess everything is in order. Will start to look elsewhere...

11 replies | 280 view(s)

11-08-2019, 10:05

builmord started a thread mep8002a IP fuel rate adjustment in Generators

In reading the TM's and threads it seems it would be prudent to check and adjust the IP's fuel rates to mitigate my units excessive vibration. Seems...

11 replies | 280 view(s)

builmord
Private

Mini Statistics

Basic Information

About builmord

Statistics

Total Posts

Total Thanks

General Information

builmord Private

Mini Statistics

Basic Information

About builmord

Statistics

Total Posts

Total Thanks

General Information

builmord
Private