Search results

  1. T

    M920 starter issues help

    Here is a picture of mine
  2. T

    M920 starter issues help

    Can you send me a picture of how your relay looks wired? I have holes all in mine and I looked at TM 9-2320-273-20 section 5-25 and want to see if mine maybe wired wrong? New shifter tower, 24v relay. Now I just get no clunks or nothing once I push the button. Last time I was getting the clunk clunk
  3. T

    M920 starter issues help

    I just ordered another solenoid incase the one I have is defective, I’ll test it here in a few days too
  4. T

    M920 starter issues help

    Hi Loose I jump Off the 2 large terminals. The clicks or clunks sound like starter area
  5. T

    M920 starter issues help

    I have a m920 that I replaced the starter, alternator, starter relay, starter push button and batteries. The batteries where old 6TLs and I figured why I was there I’d just replace everting so wouldn’t have to worry about it. I have a new shifter assembly on as well problem is they when I push...
  6. T

    NH250 and 8.3 air compressor unloaded valve kit part numbers?

    Does anyone have the part number for a unloaded repair kit for a NH250 and a 8.3 thanks
  7. T

    M923 Cummins Air Compressor Unloader Repair Kit Number

    Anyone know a good part number for a NH250 air compressor unloader valve repair kit thanks
  8. T

    M923A2 won’t build air

    Hi Wes it only builds up to 60 and may get up to 80. I put a new air dryer and brake chamber diaphrams in both rears only made a small improvement. This is my first 923
  9. T

    M923A2 won’t build air

    Have a 923A2 with the 8.3 Cummins. new air dryer and brake chamber diaphrams installed. will build up to 60 psi then pretty much stay there. previously would only get 35-40 psi before diaphrams replaced anyone have this issue before?
  10. T

    M915-M920 Cummins PT Pump No Throttle Response

    I tried to send him a message but he isnt accepting
  11. T

    M915-M920 Cummins PT Pump No Throttle Response

    Anyone ever have an issue with their PT pump not responding? I put a brand new pump on, new tanks, lines and fresh fuel and now 5 months later truck will start, only idle and shut off normally. replaced filters (inside pump and on back) which looked good, throttle shaft moves but no response...
  12. T

    M1078 starts runs for minute then loses electrical power

    Truck has brand new 6TLs, once you cycle ignition switch, starts up normal then repeats, click, no power
  13. T

    M1078 starts runs for minute then loses electrical power

    Have a 1078 built 2002 that was running normal, parked it then when go to start it runs for a minute than can hear a click then truck loses power. relay shorted?
  14. T

    M35A3 No Start

    Anyone have issues getting their A3 started after governor change? I put 8 -10 psi and get fuel in. New shut off solenoid. On the A3 is there any other sensor or switch on the truck? im very familiar with this engine on commercial side. Very rarely worked on the A3 but in other gov prefixes...
  15. T

    MEP 831 not getting over 150 volts

    Kurt. It was the switch. Just the gov giving me grief now. Magnet wants to pull and shut it off
  16. T

    MEP 831 not getting over 150 volts

    Here is pic of gage
  17. T

    MEP 831 not getting over 150 volts

    Hi Kurt 5/16 gap is correct. I put a fluke 77 and measured 0.01 and 0.00 on the L1 and 2 to N
  18. T

    MEP 831 not getting over 150 volts

    I been restoring this unit and got it started. However I cannot get over 150 volts. I have a new controller card. The unit will also run then stop. Possible gov adjust needed?
  19. T

    Has anyone made a M1031 governor linkage assembly?

    Yeah post some pics
  20. T

    What have you done to your CUCV today/lately - Part 2

    Washed and serviced my two.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks