Search results

  1. Speedwoble

    FLU-419 fuel question - part above filter housing

    “Horse graves” Note to self, don’t get on FF’s bad side.
  2. Speedwoble

    Using my SEE for real work

    Finally got around to assembling the gantry crane. I could not lift the assembled parts with the loader, so I had to use the backhoe as a crane. I also moved an Ash log that was all the loader could handle. It is now 2.5” live edge slabs.
  3. Speedwoble

    FLU-419 fuel question - part above filter housing

    Oh? Are you aware of a single issue traced back to the diagnostic wiring? I agree it is cluttered, but the pin out is available and it makes a handy test point with a multimeter. Not that I have used it as such. {edit, not trying to be sarcastic or poke FluFarm any more than I usually do. Just...
  4. Speedwoble

    Title Regis. in Texas

    You need to be working with the seller you bought from. Titles and SF-97’s come from seller. They aren’t created by the TxDOT. If purchased from GovPlanet, you have to request the SF-97.
  5. Speedwoble

    FLU419 SEE HMMH HME Owners group

    I learned not to use that drill on a concrete block wall. Tried to drill a 1 inch hole. The exit wound on the inside of the wall was 6 inches.
  6. Speedwoble

    FLU419 SEE HMMH HME Owners group

    There was someone on here that got the mount to place an auger on the backhoe in place of the bucket. They bought the adapter for a CASE 580, then rented a skid steer auger. Unbolted from the skid steer mount, bolted to the adapter for use, then returned when done. Potentially the same could be...
  7. Speedwoble

    My unimog 419 Will not go into pto gear

    Well, I would say a transmission full of water is a key clue you omitted.
  8. Speedwoble

    My unimog 419 Will not go into pto gear

    Are you in Georgia? There was a unit being sold down there that was in rough shape and had some mechanical issues. I hope you got a good price if it wasn’t shown as running. No specific gear is required. Clutch needs to be depressed.
  9. Speedwoble

    My unimog 419 Will not go into pto gear

    The PTO is a very simple operation, sliding a collar over to lock in the PTO. I assume you have the clutch in? No bad noises? I’ll try to look at my spare PTO to see if the is a rod that could get rusted.
  10. Speedwoble

    Door removal / hinge pins FLU419

    I had thought, based upon the Unimog I parted out, that the door could lift up and off like a jeep. I took a second look at mine and was not able to get it to remove. I did manage to drop one of the three nuts holding the spring on into my cab frame. So there is that. All of my pins are pressed...
  11. Speedwoble

    Dipper cylinder rod mystery , will not fold up 1.5"-4" short of latch. How to find what Length it should be?

    I confirmed the 35C and M35C use the same gland in my last line. I could not confirm all the differences between the 35C and the M35C. Known differences are the dipper cylinder(longer), the dipper arm(relieved for more angle), the backhoe mounting frame(hitch added, maybe narrower), and the...
  12. Speedwoble

    Dipper cylinder rod mystery , will not fold up 1.5"-4" short of latch. How to find what Length it should be?

    Here is where the 35C is in the catalog: I have photos of the prototypes from the 1980's and can confirm that they modified the dipper arm itself to swing tighter(It has paint burnt off so we know it was cut and welded on.) I don't know if they changed anything on the hydraulic cylinder, but...
  13. Speedwoble

    CASE M35C valve sections

    Are you always this cheery, or did we catch you on a good day?
  14. Speedwoble

    CASE M35C valve sections

    The M35C is still in the system available to dealers. I refer to it all the time. Also, be aware our backhoe seems to have more in common with the 580E based upon the dates, but a lot of parts are common. The military manuals should be the first reference. They list Case numbers.
  15. Speedwoble

    Dipper cylinder rod mystery , will not fold up 1.5"-4" short of latch. How to find what Length it should be?

    I checked against the CNH prints, and “CENTER OF HOLE TO END OF SHAFT 43-11/16 INCHES” checks out for G109187. They are 43.5 +/- a little bit. I’ll try to check the other rod prints on my break.
  16. Speedwoble

    Dipper cylinder rod mystery , will not fold up 1.5"-4" short of latch. How to find what Length it should be?

    When I am back at work, I can look up the prints. I can tell you, from the prototype photos I have seen, the dipper arms were modified from the backhoe version to fold tighter, but I didn’t think the cylinders were different. But have you stored the backhoe before the cylinder work? It is an...
  17. Speedwoble

    FLU419 SEE HMMH HME Owners group

    I believe the army specified 30wt motor oil in the lubrication order. Many, myself included, drain and refill with hydraulic oil. It is not good to mix types as additive packages can have ugly incompatiblities.
  18. Speedwoble

    FLU-419: Looking for Cartridge for Hydraulic Tools Spool On Control Valve

    Good to hear you got the problem identified. Ouch that valve is pricy!
  19. Speedwoble

    FLU-419: Looking for Cartridge for Hydraulic Tools Spool On Control Valve

    Did yours fail? Just curious because my flu has an issue where it will constantly raise the loader . I assume it is electrical because I was able to stop it by disconnecting the wires to the loader valve, but I do need to dig into them some day.
  20. Speedwoble

    Hydraulic pump

    I don’t have guidance on the replacement pump. I do have a spare from a FLU I parted out if you need one. If my pump ever fails, I would consider a larger pump to make the loader respond a little faster.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks