Search results

  1. B

    Deuce belt driven power steering complete

    I used the pump and reservoir from a mid 60's C60 dump truck. Has a Saginaw power steering box. I bought the pitman arm and steering shaft from "Waterloo equipment" if you have any ?'s... Binnalljr at yahoodotcom
  2. B

    Clutch

    I had a 5ton 72-813 I sold it.
  3. B

    Clutch

    Never had a problem shifting. Was smoke coming out from below the truck when pulling. No on oil dripping from hole. I have read that these fingers are adjustable. Loosen the two nuts and turn center
  4. B

    Clutch

    This weekend I put my deuce in a fair truck pull. When done, I let the clutch pedal out and it didn't move. Next morning still wouldn't move. I adjusted the linkage and was able to get it to move and drive it home. I saw the throw out bearing was wanting to spin. Adjusted linkage a bit more and...
  5. B

    Turn signal switch rebuild

    I took it off and opened it up. Looked fine inside. Saw no decoloration of the contacts. In mine I ran a separate ground to the steering column. Looked like was rusty , so I sanded it put it back together and worked as it should. I also to the new blinker unit off and put the old one on and...
  6. B

    Turn signal switch rebuild

    My turn signals quit. I replaced the flasher. Then noticed a small amount of smoke coming from the switch. Also heard a click under the dash I'm assuming was a relay tripping. Can the switch be cleaned? Have not taken it apart yet. Or Does it need replaced. Has any one ever used a aftermarket...
  7. B

    Late Model USAF M35A2C Registry

    Just saw this thread. My m35a2 Is 87K2297
  8. B

    Transmission install

    Clutch I'm sure is alligned. The bolts may help for sure. Thanks
  9. B

    Transmission install

    Is there any tips and secret info to installing a m35 trans mission? I have it up in close. But just can't seam to get the pilot bearing and splines lined up. Thanks.
  10. B

    I have a noisy M35A2.

    I bought the main shaft. Front shaft and the rollers from Memphis equipment. Pricey YES. But they have it and it's in it way already. Everything else looks good. Truck always has shifted smooth. So when I replace the mentioned above I'm thinking it will be just fine.
  11. B

    I have a noisy M35A2.

    Well here's what I found. The transmission is out. The actual bearings seam good. Very little if any movement. The 14 loose rollers look like hex nuts... the end of the shaft that rides on them is shot. Where can I get a new shaft and rollers?
  12. B

    I have a noisy M35A2.

    Let me start by saying it's a 1987 M35A2C.. Again I checked all the fluids. Greased all the drive line. Went for a ride. Very rattely in 3rd and 5th under a load. Drop to 4 and put it under load and no more rattle? Synchronizer bad? Is there something 3/5 share .and not 4?
  13. B

    I have a noisy M35A2.

    I put the transfer case in neutral. Transmission in 5th let the clutch out. Up to 2300rpms smooth n quiet so can't be the transmission
  14. B

    I have a noisy M35A2.

    All the rear drive line is new. I have no rusty u joints. All bolts are tight. No play in any joints. I'm leaning towards the rear drive shaft out of balance. More fuel more noise. As I ease off the fuel noise level drops. Feels much smoother. Next I'm taking rear drive shaft out, put...
  15. B

    I have a noisy M35A2.

    If that's all you can com up with for a reply keep to yourself
  16. B

    I have a noisy M35A2.

    So I put truck in neutral. Got up to 2300rpms smooth and quiet,with clutch in and out. Now put it in 5th gear with transfer case in neutral. Got it up to 2300 rpms quiet as can be. So that all said... I'm thinking rear drive shaft out of balance. Gets worse at higher speed/ rpms. Gets smooth and...
  17. B

    I have a noisy M35A2.

    When driving. It's very noisy. More so than normal. Very chattery, rattling . As soon as I depress the clutch pedal all the noise foes away? I've been told throw out bearing. Front transmission bearing. Jack shaft loose or bad u joints. Rear drive shaft out of balance. All that said where do I...
  18. B

    side window parts and a question

    Not it. I need the thin metal that holds the rubber trim that the window closes against. The metal and trim actually attach to the under side of the roof.
  19. B

    side window parts and a question

    I need two sets of the thin metal that holds the passenger and driver side roll up window rubber in place. I have new rubber molding but since I built the quad cab I need another set of the metal that's used to mount the rubber. There are a few different model trucks and probable more I don't...
  20. B

    Drive line angle

    None of the mounting points were changed when the cab was stretched. The
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks