Search results

  1. mike634

    Voltmeter click?

    Check the glow plug solenoid under the hood bolted to the fire wall
  2. mike634

    What have you done to your CUCV today/lately - Part 2

    Hold down for the bottle jack
  3. mike634

    Brushguard dimensions

    .25 inch think and 1 5/8th wide
  4. mike634

    Buying New Injectors. Delphi or Bosch?

    They are fine thread.
  5. mike634

    Stuck Brake Drum

    After a lot of pulling and prying it's off. CUCVRUS was right. Whatever it takes is the best way to get it off.
  6. mike634

    Stuck Brake Drum

    Have not had a chance to get back to fighting with it. I did pop the nail heads with no luck. The wheel cylinders are not more than 2 years old. I did open the bleeder and removed the brake line. I might try a hydraulic spreader to force it off if I can borrow one from work for the day.
  7. mike634

    Stuck Brake Drum

    My right side brake drum on my M1028 has gotten the best of me. Axle shaft is out and the locking ring is removed. E brake is off. The wheel would not move by hand when I started on it. The adjuster is frozen and I am letting it soak overnight in PB blast. I was able to work it where I can...
  8. mike634

    What have you done to your CUCV today/lately - Part 2

    That is a homemade bracket. I am not sure if you have a direct drive or gear reduction starter. They use different brackets.
  9. mike634

    Mystery wire near heater switch on m1009 ???

    The volt meter socket bulb should be a 1445
  10. mike634

    What have you done to your CUCV today/lately - Part 2

    Getting closer to being back on the road.
  11. mike634

    6.2L fuel leak

    Small hose running from injector to injector could be leaking if they are cracking.
  12. mike634

    What have you done to your CUCV today/lately - Part 2

    Got to work doing some frame repairs and knocking the rust off the frame. After a coat of KBS coating it should be back on the road. Also found my welding skills are not what the used to be.
  13. mike634

    1009 hood cable came loose or broke

    I just went through this with my 1028. The cable snapped about a foot from the latch. I unbolted the handle under the dash then I was able to lift the left side of the hood and snag the cable and pull out a few inches from under the hood. After cutting the cable I grabbed the inner cable with...
  14. mike634

    April 27 & 28, 2019: MTA Military Vehicle Show & Swap Meet (Augusta, NJ)

    I have a m1009 rear bumper for sale if anyone needs one. I can stop by the show at any time.
  15. mike634

    GEP 24-volt starter for my P400

    Hillbilly Wizard has original starters that are rebuilt.
  16. mike634

    Tail Pan Replacement

    That spot weld cutter look like it should make the job easy.
  17. mike634

    Tail Pan Replacement

    I was afraid it was welded in. I do have the bed off and flipped but I am leaning toward just patching in some metal for now. Thanks for all the help.
  18. mike634

    Tail Pan Replacement

    Has anyone replaced the tail pan on the bed of a M1028? I have all the bolts out but the old one feels like it is spot welded in or just rusted in. The part is on the underside of the bed at the back end of the bed if I am not referring to it by it's right name. This is the part below.
  19. mike634

    m1008 glow plug/wait light issue

    Did you check the glow plugs themselves? I am not sure if they are all bad if that would cause the light not to come on.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks