Search results

  1. D

    Auto to Manual trans.

    727 has been leaking fluid and need to deal with it. I have a 4speed from an '84' Dodge pickup with the granny Low. Mine has the 318 and 203 TC. What would be involved to swap the 727 with N435 or 455 ( not sure which it is as I'm typing but it is the granny Low)?
  2. D

    Hood replacement

    swapped out hood on my M880 (started yesterday and finished bolting up replacement today) ...I know but when your doing it alone, it takes longer, Problem is when closed Pass. side/right side will not close from cowel line just past the hinges . Hood sits aprox. 2" high there and lowers to...
  3. D

    M880 5.2 smoke coming out of air breather inlet

    Having trouble starting and after a start, will run and then die. After several rotations of this, smoke will eventually build up in air breather. I would guess, gasoline not burning efficiently in combustion chamber and/or carburetor and timing issues. Anyone had this happen? Thanks
  4. D

    Master Cylinder Push Rod Adjustment

    Installing a new Brake Power Booster, tag says, "Master Cylinder Push Rod Adjustment must be checked for proper clearance." How is this done? Thanks!
  5. D

    PS pump and steering gear box

    Hi, my PS fluid is milky and I wanted to change all the fluid in the pump and steering sector. Removed only line on the steering sector that would come out (first jacked up front end) and turned steering wheel back and forth. Emptied pump reservoir several times before reconnecting line on...
  6. D

    Wiring a M38A! 12V system

    I just wrote a long explanation to the problem I'm having w/ wiring in a new SRS (starter relay solenoid). It included where my wires are connected and etc. I posted it and was asked to log in again...consequently the entire message vanished when I did this. I need help in wiring a 4 post SRS...
  7. D

    Front two tires not plumb..leaning

    MY 53 M38A! front tires are leaning (when sitting) from 12 o clock to about 5 o clock. Had someone try to fix it ] but couldn't determine why. Any ideas?
  8. D

    Dist. & plugs

    On a 4cyl. Hurricane engine, I need to check location and routing of the plug wires on the distributor and engine. Been looking for 30mins. and can't find a diagram or if CW or CCW movement on a '53-M38A1..Thanks
  9. D

    Fuel tank sending unit assembly

    Anyone know where I can find the complete assembly for the fuel tank?
  10. D

    YS Carburetor for A1

    After cranking and idling, (which is no problem) if I press the gas pedal a little more the engine starts to die. If I hold it there it will die. If I push more it catches and runs fine. The rpms just past idle, 700 - 800, is where it pulls down. So if I remove my foot from the...
  11. D

    M38 A1 rear axle

    Does the M38 A1 ('53') have a Dana 44 10 spline rear axle? Thanks
  12. D

    Locker for rear differential M38 A1

    Can anyone help me find a locker for the D 44 in the M38 A1...I believe it is a 10 spline axle? I have been browsing the archives and threads gaining more knowledge but not able to lay my hand on a locker. Some have talked about going to a 19 spline axle in the D 44 and buying the proper...
  13. D

    Compartment below fuel tank

    Does anyone know what the compartment below the M38A1 fuel tank is...'53' model?
  14. D

    MB GPW axle ratios

    Does anyone know what the axle ratios are for the full floating axles on the MB and GPW? Thanks!
  15. D

    Generator

    My M38A1 was 24V but was converted to 12V. It still has the generator on it and I was curious of what I had to do to use it as a welder in the field? Thanks
  16. D

    Water proof Dist. & spark plug wires M38-A1

    My M38A1 doesn't have the WP distributor or WP plug wires. Would that mean it isn't equipped with the ventilation system for the crankcase, Trans, T/C, front and rear end, brakes, fuel tank and valve cover? It does have the metal shields where the wiring connects. Also, would there be a...
  17. D

    waterproof spark plug

    On the Hurricane waterproof spark plug what plug is used? Thanks
  18. D

    Waterproof distributor

    My M38 A-1 has been converted to 12V w/o waterproof distributor. If I add the waterproof distributor do I have to convert it back to a 24 V system? (I have the early model type made in Jan. '53.') If not how do I set it up? Thanks
  19. D

    M38A1 axle ratio

    What axle ratio will a Jan. '53' M38A1 have? It is the early model M38A1. Thanks
  20. D

    Camper top for M880

    I've seen some pictures of M880's with enclosed wood compartments. Does anyone have plans to follow or ideas on how to build a top that can serve as a camper?
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks