Search results

Back in 2016 my deuce would not start, after researching here, and help from a member here I pulled the HH and found the clip off the plunger, nothing seemed bent or broken, put all back together and truck started right up but I did notice that when you would bring up off idle with the throttle...

Tried to fire up my Deuce after sitting for about three years with the fuel system drained, dumped about 20 gal. fuel in tank replaced all three filters. The in tank pump runs, and I have fuel all the way to the inlet of the IP, but she wouldn't fire, will fire on ether but as soon as that's...

I am going to have my deuce towed by the towing co. that tows our over the road tractors and the easiest way for him to do it would be to use the wheel lift and pick up the front end. My question is for about a six mile trip, on a state route at no more then 40 MPH what should the trans. and...

I have done a search on the topic, read several good discusions that have alot of info. I read Banshee 365's tech. article with the step by step pic. very well done write up. I have the TM down loaded on the computer, makes it nice to just print the pages for what your working on take them out...

Last weekend I took the deuce for a ride then took it up to the shop to keep it inside overnight Sat. pulled it out Sun. to paint it, then then put it back in the shop till Mon. morning when I parked it outside, No oil spots on shop floor after all weekend. Wed. I thought I'd use the truck to go...

A local weekly paper in my area has a ad in this week that might be of interest to someone. The ad is for GMC military trucks says one is "cabin" chassis w/axtra cab one complete w/bed & winch 6cyl eng auto trans eng turns over free, w/1 1/2 mil. trailer No titles. $750.00 all. I have no...

Fig. 47 from TM43-0229 has a 3 color camo pattern and I was wondering how that would look with the green, brown and black colors. And if so which colors would go with which numbers on the pattern in the TM. I looked and didn't see any charts or any listing that would apply, did I miss something...

Yesterday was first nice day here in Pa. for a change could not let a little thing like no reg.tag on my deuce stop that first spring ride around the block(well maybe alittle more) Anyway that could be a storie for an other day. Hooked the batteries up, checked oil, drained prim. fuel...

I would like to have four pic. of an M35A2, one front, one rear, and one each side straight on not at an angle. If anyone would be so kind to consider E-mailing me these pic. PM me for the details. Thanks.

With the weather breaking soon (I hope) will be starting to do some body work on my deuce and was wondering if anyone would know what gauge sheet metal would be best to use to weld into the rocker panal area and the bottom of the door. I could just gauge what is used from new and match but I...

Would like some info about the cargo bed cover, mainly the stakes(uprights) the cornor pieces, and the center section. My deuce has the troop racks on and it looks like there was a wooden stake in some of the pockets with a lag bolt run in with the stake just cut off, other ones are empty. My...

The air compresser belt on my deuce is very loose. It looked to me like a split pulley but was not sure so looked up in the TM and I was right, the TM list a special spanner wrench to adjust the pulley. My question is taking into consideration the right tool for the right job is there any other...

I'm not sure the width of the axle on the M105 would it fit inside the bed of a deuce. Wed. I will be going to Chambersburg to pick up my M105 trailer will tow about 10 mile with a Ford F350 pick-up to the trucking co.where my deuce has been stored 6/20. Will load the deuce on a detach...

Not sure if this is right place for this but I'll give it a try Hope you guys are patient with a first time out of the test forum. Have thought about having my own M35 for a long time (like since I was a kid) and now is the time to act (before my wife changes her mind). The Havre De Grace, Md...

Not only am I new here but also new to this computer stuff so I hope I'm going this right and not messing up anyone who knows what they are doing