Search results

I hope this is the correct category of truck. I have a part that has been buried in my parts bins for a couple of years. It is NOS and I believe by the part number it is for the HEMTT family of trucks. The part number is 85570-06-24P. Before I list it on ebay I would really like to know what it...

Last season we were using the Dodge and bent up the cab top bow pretty bad. I have been contacting and waiting for a couple of months for Midwest Military to get them back in stock and yesterday they indicated it just wasn't a priority for them. We're trying to get the Dodge in shape to head out...

I'm looking for a new or used in good shape arm that attaches to the M37/M43 steering gear box and connects to the drag link. It is the small arm that has a ball on the end. If anyone has some parts left over from a power steering conversion or just parts in general and has one of these they...

I bought a Dodge W400 truck near Oklahoma City and will be heading there from near Denver to pick it up on Decmber 27th. I'll be towing an 18 foot dovetail and can carry upto 9,000 pounds. I'll have the bed of my 3500 empty on the way back. If I can help anyone out let me know. The description...

The administartors closed the thread because it actually belongs in the classifieds. By reading the post I have questions. It states it has a 251. These were used in the Canadian versions. Because the 251 is 2 inches longer than the stock US M37 235cuin engine, the folks in the north had a...

I have 4 boxes weighing in about 75 pounds each and about 8 feet long by 1 1/2 by 1 1/2 feet square. No hurry. If you are coming through anywhere in Colorado from the Ft Worth area and have the room to haul these four boxes please get with me. Thanks. Regards, M376X6

Found a completely rusted up dual output PTO for the M37 series. I have a set of gears from AB Linn. The dual shaft is pitted badly around the seal contact points so I'll use a machineable epoxy to return it to correct OD on both sides and then press fit sleeve them. The reverse gear bearings...

Here are a few pics from this years bull elk hunt. Next week we go on our cow elk hunt. Regards, M376X6

It's too late for this year but I was thinking maybe a Mountain States Rally would be a good thing. There are some super trails not far from here that go up to timberline and can be a bit tough. One is the trail to Bill Moore Lake above Empire, CO. The snow drifts usually get up to 30 feet deep...

Decided to standardize my two trucks and ended up using four of my new 11.00-16 XL's on the 4X4. I'm short 2 XL's for my 6X6. Would anyone have or know of anyone who has two of the XL pattern tires in 11.00-16 available in near new or new condition? It would be really nice if they were fairly...

I'm at work with some nice folks trying to buy an M101A1 I have for sale. I've gone through the Search and have tried desparately on the web to find the number of inches between the wheel wells. Anyone know this off the top. I imagine it is around 40 to 50 inches but getting old and don't...

Hi Ethan, Bryan here in Colorado. I didn't want to talk about this in the hub thread so I brought it here. You mentioned de-splining the stock hubs for your truck. Do you plan on adding any type of bushing to the hub to help with contact from the splines? How were you planning on removing the...

I've had a Dodge 360 V8 in the 6X6 for over 15 years and have tried to keep it 24 volt throughout except the starter which would have to remain 12 volt. I finally ran out of patience with the various dropping resistors and relays to start the truck on 12 and run it and various accessories on 24...

I have three shackles and need a fourth. They are made by CM Forge whose distributors freak out at the idea of dealing with military items. The number on the shackle is 19207 12355838. These are normally installed on the M116's. I need just one. Thanks Regards, M376X6/M354X4

I haven't priced one lately but what would be a going price on a complete winch setup. It includes the following: Braden LU4 Winch Bumper and extensions and mounting hardware PTO and shift lever with locking bracket, rubber floor seal, and PTO to winch shaft. Cable with chain lead and...

I'm working on a project and I need a lug nut that is used on the current LAV's. If not the actual lug nut then the dimensions and thread size and even a picture would be terrific. I need to see what is the equivalent available in the civilian market. Thanks. Regards, M376X6

Anyone know of any Bobbed deuces here in Colorado or close by? I'd really like to have one rolling by next spring and would like to look first hand at one and have some conversation with the owner. Thanks Regards, Bryan

As I finish the 24 to 12 conversion on the M37 6X6, I have re-installed the jumper cable jack. I searched and found where I believe one of the surplus houses had the jumper cable connectors for sale but are Out Of Stock. Would anyone have one or two laying around. I don't need the cable part as...

I have a post on the M37 portion that shows the adapters I make for the M37 variants and Power Wagons. I have the dimensions and can make a set for the M715 series bolt pattern. This would be the first and might take a few extra weeks as I machine the first and make any changes needed after beta...

I've just shipped another set of adapter plates to a friend and fellow enthusiast out in California. I have another set just about ready to ship and thought I would offer them here on Soldiers. If anyone is interested please email me at b r y a n s a g e @ a o l . c o m please omit the...