Search results

I purchased a Rhino tire carrier for my M998. The pivot pin is slightly bent. I have been searching to see if anyone has successfully straightened one, but have had no luck. I was thinking I could disassemble the tire carrier , clamp the swivel pin in the vise, and heat it with a torch. I plan...

I am looking for the white 18gauge? teflon covered wire thaat is used in the A2 harness so I can build the middle part of my 4L80 harness. Is it available? I purchased a NOS harness from a APC or something to get the male and female connectors as well as the rubber coated black wire. I have...

Too often I search for answers to a problem and I find someone else with the exact same problem. It seems like there is rarely a resolution posted. Well here is my problem and solution. On my M998 when I activated the turn signals both fronts functioned nornally. The rear turn signals...

I am having a friend change my head gaskets and cylinder liners and pistons. I ended up having 3 cylinders with broken rings and my head gaskets were leaking oil. I bought 6 pistons and sleeves and when they were unwrapped I have 1 piston which does not match and I am missing 2 squirters. I am...

I just started trying to put the air-o-matic steering on my truck. I received it with springs and cups out of the valve and I need to know how all of this stuff goes together. I looked at the one TM 9-2320-386-24P but it does not show the assembly of the parts. I assume maybe only one spring...

My neighbor has a M931 (I think) and it is not running right. We did a local homecoming parade last week and his truck started to run bad on the way home. He was idling in traffic and said he heard the engine sound change. He went to take off and the truck chugged and black smoked. He made it...

Can someone point me in the direction of a way to remove a stuck fuel injector? Its stuck bad and is on a LDS 427-2. I am able to turn is with some great effort after heat, a air chisel, PB blaster, WD-40, and deep creep. Its no where near coming out. I was even able to hit it wiith a slide...

I talked to Todd at the Clermont County fair today about doing some exhibition pulls at the fair this year. I was told that I could pull Friday night July 25 after the tractors. I was also told that if I could get enough interest they would consider a class for next year. So far I have 4 trucks...

So, I have a M35A3 bed on my A2 and I need some help hooking up the rear auxiliary lights. I have the 3 light panel in the back as well as the 2 side lights. I do have the wiring harness for the panel. Is this as simple as matching numbers up? I always hated the big hole in the back of my bed...

Could one of the experts tell me if these are in fact CCKW top bows and give me a clue as to their value? They are too narrow for my M35A2 bed and have leather strap remnants . Wood is very nice .

Well some idiot (me) adjusted the output on my alternator and did not replace the plug. My rheostat was screwed up by the previous owner and I had to keep adjusting it. That being said I got it right and it was holding and I forgot to put it back in. I went to the Haspin rally and played in the...

I have been in the market for a heater, a winch, and a hard top since I bought my truck. Obviously I want the best bang for my buck but I cannot believe the prices that people are asking for these parts. I see where people buy entire trucks for what they want for a winch alone. I guess it is the...

I was changing the fluid in my rear most differential and I decided to take the jiggly cap vent out to make sure it was not clogged. I had a little oil on the inside of the rear rim but for the life of me I could not see where it came out of. Obviously the fluid is from the rear diff. When I had...

I was told that someone around here makes stencil kits for the Vietnam era that would be correct for my Deuce. I am going to paint it the original OD green and want to put at least the stars, truck serial number, and US Army. I ordered the paint yesterday and hope to have it by this weekend or...

Ok guys what did I mess up? I reached into the truck to start it without getting inside and flipped the accessory switch on then hit the start button not realizing I forgot to push the fuel cut off handle back in. NOW when I crank the truck instead of the 1/2 turn of the engine to start I have...

Is there a pattern out there for the compressor wrench? It would be cool if someone had a pattern or traced one on a 8 1/2 X 11 sheet of paper and scanned it in so tight wads with scrap steel could make their own. Thanks.

I have caught the Deuce modification bug. I turned up the fuel after I added the turbo and took the forum's advice and added a pyro gauge first. What do you guys think? I bought a Autometer pyro gauge with probe for like $82 shipped and added a $5 gauge mount from O'Reilly auto parts. I...

I need some help locating a coolant leak that just developed on my Deuce. I was walking by and noticed something wet on the ground. I popped the hood and saw antifreeze on top of the front diff and then as I looked further it appears it is all the way on top of the head between the valve cover...

I have been trying to figure out my alternator issue as well as learning/absorbing as much as I can about the M35A2. I have seen a few pictures where it appears that the 60 amp alternators have 3 small wires, 1 cable to battery,and 1 cable to ground. My setup has the 2 cables but only 1 small...

As a new member to this site I have found it very useful so far. The one BIG drawback of the forum is that the search feature here apparently is set on kill. I am a member of probably 10 different forums and this one by far is the hardest to find information on. I do a search for diagnose...