Search results

Sent out fuel pump today to get remanned there is a small line between the block and pump that is rusted as well as the steel lines feeding injectors. researched new lines of part numbers but no luck on small line. Feed lines were available but without picture. I remember seeing a thread where...

Have an 816 with 250 cummins motor was rebuilt 1980. New pump was put on 8 years ago. The drip is located on the front of pump . there is one bolt at 8 o clock and another at 4 o clock and 1 allan bolt at 6 o clock . It only drips sometimes and not much maybe 4 ounces then it wont drip for...

Took apart clutch linkage from pedal to shaft on bell housing. Had to clean threads and clevis went to adjust free travel and noticed very little movement on throw out bearing shaft about 1/4 play took trans cover off noticed head of air chamber bolt was against throw out bearing shaft with no...

Purchased 12 g177 on rims with 80 to90% tread for $135 peace. The valve stems are cut so I need to find 11.00-20 tubes and remount. Any one with a source for these would appreciate info . They will not be here till Thursday called vendor he did not know if they were radial tires don't know...

Friend bought an 1971 816 the power divider shaft is one piece, mine has split shaft the TM shows the split shaft any advice to drop shaft out. Took out bolts on both velocity joints not enough play to remove shaft any advice would be appreciated have to replace boots and seals. Thanks Scott

Any date set Thanks

I am going to bid on some pumps GL has on auction from Ohio shipped to New York anyone with advise would be appreciated. Items will fit in a 6x6 foot crate. Thanks Scott

Was going to bid on these will they go on 11:20 rims with any problems. thanks

My friend gave me some tow slings they are several layers of strapping 1 1/2 about 20 foot long any one use one .Or is it in a TM somewhere thanks Scott

My top had quite of few small rust holes near the bottom left and right side also along top sides. We sanded and primed the bad spots brushed on a thin layer of Herculiner bed coating and applied the nylon mesh sheet rock tape. This dried overnight then applied two coats to the entire top four...

Want to see if anyone has a serviceable hoist motor or rebuilt . Tried a couple of takeoffs main shaft rusted could not get the O rings to seat properly . It seems if they sit to long the upward pitch on the motor takes in water and rust the shaft. Appreciate any replies Scott

On the last step of rebuild of the ole wrecker doing the cab interior one question the gauges have a raised rib on one terminal on the plastic gauges is this the hot side. My brother dismantled it and at one time the harness was repaired with different number wiring which I sorted out today...

Renovating the inside of the cab got tired of running paint on dash.plus had to rewire underneath dash. Screws were rusted had to hit them with center punch and work them out with penetrating oil one came out with a screw driver. Cleaned up all the plates some our dull want to clear coat them...

Anyone have a source for these it is a simple relay appreciate any help. Thanks Scott

Anyone know if this is available at NAPA or elsewhere Cold Start Relay above flasher unit Thanks Scott

I wanted to replace the oil line from block to gauge fitting always leaked at the bulkhead fitting on firewall. On the other side t fitting with starter lockout switch never knew it was there how does this function is wire 93 go to ground in the protective control box and works on not enough oil...

Have to go to NAPA for parts does anyone know if there is a part number for the filter mine is on top by governor older model. If not I will go to Cummins dealer thanks Scott

Leak started where the fan hub mounts to the timing cover into the front timing cover. The adjustment bolt for the fan hub was missing and one of the hub bolts worked out and is rusted in place. Put a wrench on it would not move so im going to pull the radiator and replace all the belts and pump...

I was going to bid on some trailers has anyone with experience ever picked up a trailer or vehicle at Dix do they help load if you send a hauler down with a flatbed. Also any knowledge if Gov Planet has titles for these and if they allow you on base to view equipment. Thanks for any info always...

Hey Guys Happy New Year I am away from home there is a junk yard where we are visiting with a lot of rims need the bolt center pattern and the hub opening have split rims want to get solids m816 Thabks for any replies Scott