• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

What do you build?

6x6TRex

Member
261
2
16
Location
Flint, MI
A few more

Weld tests! I'm an AWS level 1 welder
198266_10151518753756562_378569833_n.jpg15234_10151528083951562_1099276585_n.jpg215069_10151564621241562_364378698_n.jpg

Badland ST4 buggy project that I traded for a Jeep
0322112348.jpg

A German Sdkfz 250/1 replica I helped a friend build out of a heavily modified 89 Blazer
Finished.jpgIMG_5014.jpg
Completely finished video:
http://www.youtube.com/watch?v=v9nPZULsc1g

German kettenkrad replica I helped a friend build
krad.jpg

Plus a few gokarts and a steel propane powered potato cannon I don't have pictures of.
 

Rusty nuts

New member
91
4
0
Location
Oregun
While mine is nothing close to a "Terrible Herbst" build, I have a lot of fun in it.

image.jpg
image.jpg
image.jpg
image.jpg

Motorcycle carrier for the back of the Moho.

image.jpg
image.jpg

Rifle dueling tree made with AR500 plates.

image.jpg
 

Rusty nuts

New member
91
4
0
Location
Oregun
It is a N/A Honda 3.5 with a Mendeola 2d. Our dunes up here in Oregon are not as open as say Glamis or St Anthony's, we have lots of trails with trees so I built a 2 seater that is only 88" wide and a 108" wheelbase...it's a fun little car.

My first build from scratch was a 4 seater with a 450hp LS1.....you can probably see a little Tatum influence in that build :D
 

Attachments

quickfarms

Active member
3,495
22
38
Location
Orange Junction, CA
Here is a little project that I have been working on.

It is a Gannon Earthcavator. It is an early one made for a small tractor. It is being converted from a FD-032 to an FD-042 on steroids.

This is what I started with, after the original mounts had been removed.

ImageUploadedByTapatalk1412636937.476020.jpg

The original bent moldboard was removed.

ImageUploadedByTapatalk1412637044.820119.jpg

The carcuss was then sectioned for widening.

ImageUploadedByTapatalk1412637096.111854.jpg

The scarifier bar was widened and an additional shank pocket was added

ImageUploadedByTapatalk1412637167.874257.jpg

The new moldboard, twice the thickness of the original and four additional braces were added.

ImageUploadedByTapatalk1412637276.163832.jpg
 

maddawg308

Well-known member
Steel Soldiers Supporter
10,852
723
113
Location
Front Royal, VA
Great fab work to the OP, but now you've gone and kicked over the hornet's nest. M920 is gonna come in here, share his pics, and kick your a$$. Well, you'll be impressed, anyways....
 

marchplumber

Well-known member
Steel Soldiers Supporter
3,651
2,416
113
Location
Peoria, Illinois
Great fab work to the OP, but now you've gone and kicked over the hornet's nest. M920 is gonna come in here, share his pics, and kick your a$$. Well, you'll be impressed, anyways....
Soni ROCKS!!:not worthy: Nice lookin table. Should hold what ya put on it! LOL!! Thanks for sharing!

God bless,
Tony
 

tobyS

Well-known member
Steel Soldiers Supporter
4,820
815
113
Location
IN
Good Pete...at least it doesn't look like you spit weld on it. That should hold the branch together.

I can never quite get my welds to have such a nice green color however.

I went out to fab today and the LP gauge was leaking, so found another. Then tried to start the Hobart but a small prime didn't do it. Yep, out of gas. Went to town with a bit of scrap in between rains and brought fuel back.... ran into a hail storm. This was the largest hail I have ever seen (some golf balls) and thought any minute my windshield would shatter. I pulled off the road next to the largest tree I could find and got a very small amount of shelter...but no broken windshield or too bad of denting. I waited it out and drove home only to get hit again with hail real hard.

I gave up on welding today.
 

Hoefler

Active member
1,096
20
38
Location
White Bear Lake,MN
IMG_1004.jpgIMG_1072.jpgIMG_0315.jpgIMG_3893.jpgIMG_1189.jpgIMG_0765.jpgIMG_3481.jpgIMG_1192.jpgIMG_0976.jpg

Here is some fab we have done for us. My company is in the pneumatic convey industry for industrial food production like breakfast cereal, snack chips and protein foods. Almost everything we do is in stainless steel-laser cut flat patterns and TIG final weld. I have tried to TIG weld myself-it was a no go. I have great respect for fabricators-welders and the skills they have. Workmanship like that Soni guy on SS is tough to get.
Stickers on on the front entrance of my building.
Pete
 

Attachments

Last edited:

DrillerSurplus

New member
443
7
0
Location
Salt Lake City. UT
Pete, that is some cool looking stuff. I've never tried TIG, but I know after years of welding thick metal with lots of amperage, I'd have a hard time with anything thinner than 1/4" without some training.
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks