Page 6 of 6 FirstFirst ... 2 3 4 5 6
Results 51 to 54 of 54

Thread: M939 winch install (Pics & Video)

  1. #51
    2 Star General lindsey97's Avatar
    Join Date
    Jul 2014
    Location
    wynnewood, oklahoma
    Posts
    736
    Thanks
    1,356
    Thanked 517 Times in 288 Posts

    Default

    I'm good. Still need to get a pto from you sometime.

  2. #52
    2 Star General lindsey97's Avatar
    Join Date
    Jul 2014
    Location
    wynnewood, oklahoma
    Posts
    736
    Thanks
    1,356
    Thanked 517 Times in 288 Posts

    Default

    DSCN3299.jpgDSCN3300.jpgDSCN3301.jpgDSCN3298.jpgDSCN3297.jpg

    Finally got my winch setup installed. Front bolts are 1/2-20, with lengths of 1.0", 1.5", and 2.0".

    Oil capacity of the reservoir is approx. 7.25 gallons. Hydraulic filter is a Fram C1666 or Wix 51467.

    Specs on the 2 hoses going to the winch from the valve body are: 91" in length, 3/4" hose, JIC #10 female fittings on each end, with a 90 deg. male to female JIC #10 elbow on each hose for the pump end.

  3. #53
    Corporal STLZombieHunter's Avatar
    Join Date
    Mar 2014
    Location
    TROY, MO
    Posts
    35
    Thanks
    15
    Thanked 12 Times in 7 Posts

    Default

    Very good write-up. Thank you Jacob and all the others who contributed.
    STL Zombie Hunter
    -keeping St. Louis Zombie-free since 2008


    1985 M923 on 16.00R20 XZL
    1987 M1038 HMMWV 6.5 Turbo
    M989A1 HEMAT Ammo Trailer

  4. #54
    4 Star General 86m1028's Avatar
    Join Date
    Jul 2008
    Location
    Murphy TEXAS
    Posts
    1,681
    Thanks
    368
    Thanked 407 Times in 277 Posts

    Default

    Great write up !!!

    I would like to add a few things I have learned.
    This is firsthand experience not guessing not what I thought fit or didn’t.
    My “experience” is as follows
    Removed complete setup from an AM General m925a1
    Installed most of this “kit” onto a bmy 923a2
    Removed all of this from the bmy.
    Found shift towers different, pto shaft length, pto is different, hood rod different length.
    The a1 pto would NOT fit in the bmy frame.
    I dont understand the issues removing or installing the pto in an A0 or A1 frame.
    I had plenty of clearance, no jacking or moving of trans.
    The only issue I had again was trying to install the earlier style pto in the bmy a2.
    It will NOT fit, even installing pto with trans completely out of truck.
    Yes, it bolts up BUT comes in contact with frame when trying to reinstall trans in truck.
    My bmy did not need any holes drilled in frame.
    M1028A1. 350/4l80E/205
    M1028A1, M1031 x2
    M1008A1
    M923A2
    M936A2
    M916
    M715 (big pile of parts)

    M989A1 for sale

    Lots & lots of military trailers

Page 6 of 6 FirstFirst ... 2 3 4 5 6

Similar Threads

  1. Replies: 7
    Last Post: 02-27-2013, 01:24
  2. M939 Air Conditioner Install
    By quickfarms in forum 5-ton and up
    Replies: 4
    Last Post: 05-17-2012, 17:39
  3. Deuce is now WW or winch install pics.
    By ida34 in forum The Deuce
    Replies: 34
    Last Post: 04-27-2011, 21:32
  4. Pics of my rear electric winch install on the 5-ton
    By dma251 in forum 5-ton and up
    Replies: 20
    Last Post: 03-13-2007, 19:22

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •