Page 2 of 2 FirstFirst 1 2
Results 11 to 20 of 20

Thread: continental multifuel

  1. #11
    Private
    Join Date
    Feb 2019
    Location
    McMinnville Tn
    Posts
    10
    Thanks
    0
    Thanked 6 Times in 2 Posts

    Default

    It will run for about 30 seconds sometimes then sometimes it will run for 3 minutes but smokes the whole time

  2. #12
    Private
    Join Date
    Feb 2019
    Location
    McMinnville Tn
    Posts
    10
    Thanks
    0
    Thanked 6 Times in 2 Posts

    Default

    I have had it start one time and run for 15 min or so until I shut it off but I never gets past a fast idle even with throttle wide open but was running fine when it was parked about a month ago and when it ran for 15 min it smoked the whole time but won't rev up like it's not getting any fuel to open up and run I have not taken fuel lines off at the injectors to make sure fuel is going to them but have taken return line off and turned the motor and watched it squirt fuel out

  3. #13
    dumpsterlandingfromorbit! gimpyrobb's Avatar
    Join Date
    Dec 2005
    Location
    Cincy Ohio
    Posts
    27,353
    Thanks
    2,401
    Thanked 8,544 Times in 4,467 Posts

    Default

    Whatever the issue is, its pointing towrds "fuel related". I'd dig into the hyd head so you know its good, then move on from there.

  4. The Following User Says Thank You to gimpyrobb For This Useful Post:

    SCSG-G4 (02-12-2019)

  5. #14
    Private
    Join Date
    Feb 2019
    Location
    McMinnville Tn
    Posts
    10
    Thanks
    0
    Thanked 6 Times in 2 Posts

    Default

    Got the hh off button is still on

  6. #15
    4 Star General /Moderator doghead's Avatar
    Join Date
    Jan 2006
    Location
    NY
    MVPA
    8675309
    Posts
    25,814
    Thanks
    2,480
    Thanked 13,623 Times in 5,901 Posts

    Default

    Is the drive key(shaped similar to a chevy bowtie) in place and not broken? It is on that HH tappet shaft and is what makes it rotate.
    M817, M818, M819, M35A2 w/w, M35A2, M109, M105, M116A2, M101A2, Pioneer tool trailer, MEP-002, MEP-017A, 5ton winch shear pins, Oral-B toothbrush

    Ah Beefco Industries Northeast marketing associate

    Don't judge a fish by its ability to climb a tree

    https://www.youtube.com/watch?time_continue=12&v=T6BTcEwtmZo


  7. The Following 3 Users Say Thank You to doghead For This Useful Post:

    cattlerepairman (02-05-2019), Floridianson (02-05-2019), SCSG-G4 (02-12-2019)

  8. #16
    Private
    Join Date
    Feb 2019
    Location
    McMinnville Tn
    Posts
    10
    Thanks
    0
    Thanked 6 Times in 2 Posts

    Default

    I believe that's the thing I just found that is broke

  9. The Following User Says Thank You to jacob bost For This Useful Post:

    SCSG-G4 (02-12-2019)

  10. #17
    Sergeant Major
    Join Date
    Oct 2014
    Location
    Albany Ga
    Posts
    161
    Thanks
    4
    Thanked 132 Times in 66 Posts

    Default

    I think you found your issue keep us posted

  11. The Following User Says Thank You to Welder1 For This Useful Post:

    SCSG-G4 (02-12-2019)

  12. #18
    4 Star General /Moderator doghead's Avatar
    Join Date
    Jan 2006
    Location
    NY
    MVPA
    8675309
    Posts
    25,814
    Thanks
    2,480
    Thanked 13,623 Times in 5,901 Posts

    Default

    It usually breaks because the tappet shaft was stuck(could not rotate).

    Clean with carb and choke cleaner and replace it. Do not use anything abrasive on the shaft.

    Should be ok after that.
    Last edited by doghead; 02-05-2019 at 13:51.
    M817, M818, M819, M35A2 w/w, M35A2, M109, M105, M116A2, M101A2, Pioneer tool trailer, MEP-002, MEP-017A, 5ton winch shear pins, Oral-B toothbrush

    Ah Beefco Industries Northeast marketing associate

    Don't judge a fish by its ability to climb a tree

    https://www.youtube.com/watch?time_continue=12&v=T6BTcEwtmZo


  13. The Following 3 Users Say Thank You to doghead For This Useful Post:

    marchplumber (02-05-2019), QUADJEEPER (02-05-2019), SCSG-G4 (02-12-2019)

  14. #19
    4 Star General /Moderator doghead's Avatar
    Join Date
    Jan 2006
    Location
    NY
    MVPA
    8675309
    Posts
    25,814
    Thanks
    2,480
    Thanked 13,623 Times in 5,901 Posts

    Default

    Now is also a good time to replace the rubber orings.

    For immediate parts replacement , try Memphis Equipment, or White Owl, or Eastern Surplus or Boyce Equipment.

    Otherwise, someone on the site may have what you need.
    M817, M818, M819, M35A2 w/w, M35A2, M109, M105, M116A2, M101A2, Pioneer tool trailer, MEP-002, MEP-017A, 5ton winch shear pins, Oral-B toothbrush

    Ah Beefco Industries Northeast marketing associate

    Don't judge a fish by its ability to climb a tree

    https://www.youtube.com/watch?time_continue=12&v=T6BTcEwtmZo


  15. The Following User Says Thank You to doghead For This Useful Post:

    SCSG-G4 (02-12-2019)

  16. #20
    Private
    Join Date
    Feb 2019
    Location
    McMinnville Tn
    Posts
    10
    Thanks
    0
    Thanked 6 Times in 2 Posts

    Default

    I swapped it with another hh I had cranked it up ran great thanks guys for all your responses if not I would of still been sitting there

  17. The Following 5 Users Say Thank You to jacob bost For This Useful Post:

    cattlerepairman (02-05-2019), doghead (02-05-2019), marchplumber (02-05-2019), porkysplace (02-05-2019), SCSG-G4 (02-12-2019)

Page 2 of 2 FirstFirst 1 2

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •