Page 2 of 2 FirstFirst 1 2
Results 11 to 19 of 19

Thread: FLU419 Removing attachments

  1. #11
    Sergeant Major Lust4GreenSteel's Avatar
    Join Date
    Aug 2012
    Location
    KC MO
    Posts
    154
    Thanks
    123
    Thanked 209 Times in 80 Posts

    Default

    Had I been the OP, I would not have irrigated (Pzzd Off) one of the most likely and most able members to be of help. But, that is just me.
    M35A2 (BGT) loved but sold

  2. The Following User Says Thank You to Lust4GreenSteel For This Useful Post:

    The FLU farm (04-15-2019)

  3. #12
    Colonel Speedwoble's Avatar
    Join Date
    Jan 2009
    Location
    New Holland, PA
    Posts
    387
    Thanks
    64
    Thanked 163 Times in 109 Posts

    Default

    Quote Originally Posted by Jamesm417 View Post
    If this forum is not a means to share information between people with similar interests, what is it? Simply group masturbation for those who think they have know everything, and have all the answers?
    Ok, start sharing. Why should I take time out of my day to type up a procedure that you are too lazy to look in a TM. They exist for a reason.

    Personally I do think this forum gets too wordy at times, but I take what I get when it’s free.

  4. #13
    Private
    Join Date
    Mar 2018
    Location
    Alaska
    Posts
    13
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Quote Originally Posted by Speedwoble View Post
    Ok, start sharing. Why should I take time out of my day to type up a procedure that you are too lazy to look in a TM. They exist for a reason.

    Personally I do think this forum gets too wordy at times, but I take what I get when it’s free.

    What makes you assume I did not try to find it in the TMs?

  5. #14
    Sergeant
    Join Date
    Dec 2017
    Location
    Central / Washington
    Posts
    86
    Thanks
    14
    Thanked 36 Times in 26 Posts

    Default

    Whoa pump the brakes there super chief.

    Yes, good info in the TMs. The time to read through the main thread (actually read posts 1 to infinity) is time well spent. Not saying you didn’t.

    As someone who has removed and reinstalled both, all i would say is have a helper and be careful. When reinstalling the backhoe, it helps to lift the implement up into the locks (bottom hooks) as an alignment aid.

  6. The Following 3 Users Say Thank You to Pinsandpitons For This Useful Post:

    Sgt Jiggins (04-17-2019), SpoiledSpud (04-16-2019), The FLU farm (04-16-2019)

  7. #15
    Private
    Join Date
    Mar 2018
    Location
    Alaska
    Posts
    13
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Thank you, Sir.

  8. #16
    Corporal
    Join Date
    Oct 2018
    Location
    Northern (ID/WI)
    Posts
    31
    Thanks
    38
    Thanked 5 Times in 4 Posts

    Default

    Hey Jim,
    Check out this link to an index that Ron put together. Looks like there may be a few replies to piece together a clearer picture for you.
    Spud

    https://www.steelsoldiers.com/showth...=1#post2199402

    Post 649 from Bikers33

    https://www.steelsoldiers.com/showth...=1#post1920083

    Put the backhoe into a 3 point stance (2 outriggers and the bucket). Remove snap rings from the 2 top pins and bash them out. Use outriggers to make it easier. Unlatch two bottom locks (with the lever on the side of the truck). Disconnect hyd. hoses and join them together.. Block underneath the center so it wont sag. Join the hoses on the back of the truck as well.....enjoy FUN MODE!!


    Quote Originally Posted by Jamesm417 View Post
    I'd like to learn how to remove the attachments while I work on the hydraulic cylinders.

    Does anyone know where I can find this information?
    A link would be very appreciated.

    TIA.

    Jim
    Last edited by SpoiledSpud; 04-16-2019 at 22:45.

  9. The Following User Says Thank You to SpoiledSpud For This Useful Post:

    Sgt Jiggins (04-17-2019)

  10. #17
    Sergeant
    Join Date
    Dec 2017
    Location
    Central / Washington
    Posts
    86
    Thanks
    14
    Thanked 36 Times in 26 Posts

    Default

    One more thing that makes life easier for loader re-installation; grease the upper and lower mounts a little. They tend to stick and hang up just when they should drop into place. Of course you'll use the implement functions to help micro align and jiggle things into place.

  11. #18
    Private
    Join Date
    Mar 2018
    Location
    Alaska
    Posts
    13
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Thank you. That’s great information.


    Quote Originally Posted by SpoiledSpud View Post
    Hey Jim,
    Check out this link to an index that Ron put together. Looks like there may be a few replies to piece together a clearer picture for you.
    Spud

    https://www.steelsoldiers.com/showth...=1#post2199402

    Post 649 from Bikers33

    https://www.steelsoldiers.com/showth...=1#post1920083

    Put the backhoe into a 3 point stance (2 outriggers and the bucket). Remove snap rings from the 2 top pins and bash them out. Use outriggers to make it easier. Unlatch two bottom locks (with the lever on the side of the truck). Disconnect hyd. hoses and join them together.. Block underneath the center so it wont sag. Join the hoses on the back of the truck as well.....enjoy FUN MODE!!

  12. #19
    4 Star General The FLU farm's Avatar
    Join Date
    Dec 2015
    Location
    The actual midwest, NM.
    Posts
    2,450
    Thanks
    1,070
    Thanked 1,083 Times in 765 Posts

    Default

    Hmm. Somebody should post that info in the main thread, for everybody to see.

Page 2 of 2 FirstFirst 1 2

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •