Results 1 to 3 of 3

Thread: MEP-802/MEP-803A Remote Start Kits

  1. #1
    2 Star General
    Join Date
    Jan 2012
    Location
    Massachusetts
    Posts
    617
    Thanks
    56
    Thanked 786 Times in 357 Posts

    Default MEP-802/MEP-803A Remote Start Kits

    Remote Start Controller Kits
    For use in MEP-802A & MEP-803A Generators
    WiFi Remote Control & 2-Wire Start/Stop

    Features include:
    ∑ Remote genset Start/Stop via WIFI via cell phone, laptop, tablet
    ∑ Direct WiFi communication. No router needed. Works during power failures.
    ∑ 300 foot plus WiFi range. Password protected
    ∑ Browser display of all engine and generator operating parameters on remote WIFI device. Parameters nearing extremes are highlighted in red text.
    Ambient Temperature
    Battery Voltage
    AC Voltage
    AC Output Frequency
    %Load
    Fuel Level
    Coolant Temperature
    Oil Pressure
    ∑ Remotely Enable and Disable the Auxiliary Fuel Pump
    ∑ Remote control of the Contactor with the Contactor state displayed
    ∑ User calibration of all parameters
    ∑ Data Logging of all parameters as well as engine hours and Start/Stop count. Min, Average & Max values logged every 10 seconds.
    ∑ Two wire remote Start/Stop for use with ATS or other contact closure
    ∑ Transfer between WIFI and Manual control while running
    ∑ Automatic Pre-Heat below 40 degrees F

    Additional features
    ∑ User programmable durations and delays for all phases of start up and shutdown. Separate delay settings for WiFi Start/Stop and 2 Wire Start/Stop
    Pre-Heat duration
    Fuel System prime duration
    Cranking duration
    Warm up
    Stop command to contactor open delay
    Cool down delay
    ∑ Antenna and connector are IP65 rated for water resistance.
    ∑ Retains full manual control of the genset
    ∑ Controller is conformally coated to seal out moisture.
    ∑ Includes Controller, wire harness, all hardware for installation & manual
    ∑ 1 year warranty

    I personally assemble each of the Controllers and wire harnessís. Once built each Controller is tested in a generator simulator and then installed in an MEP-802A, tested and initially calibrated to assure a defect free unit.

    Users Manual --> https://drive.google.com/open?id=1s2...txV0gdc9nocbYM


    Ordering Information
    Cost: $390 Includes USPS Priority Shipping in the US
    PayPal & Checks accepted. Quantity discounts available

    To order email me at: kurtklopp@gmail.com
    Be sure to include the following information:
    1) Name & Mailing Address
    2) Payment Method
    4) PayPal email address if using PayPal

    Controller mounted on control cube
    Installed.jpg

    Controller Circuit Card Assembly
    Controller.jpg

    Pre-Assembled wire harness
    Harness.jpg

    Installation & Users Manual plus mounting hardware
    Manual & Parts.jpg

    Sample phone screen when running
    Main Screen Running.jpg



    Sample phone screen of Min, Av, Max statistics table
    Data Log Table.jpg

    Data Log.jpg

    Sample phone screen of calibration adjustment
    Pre-Heat Duration.jpg


    Feel free to email me with any questions!
    Attached Images Attached Images
    Last edited by kloppk; 08-23-2019 at 10:16.
    MEP-831A Governor Controller Replacements for the SLC100, 2990-01-477-1371, 98-19539. https://www.steelsoldiers.com/showth...90#post2233190
    MEP-802A/MEP-803A Remote Start Kits
    https://www.steelsoldiers.com/showth...92#post2233192
    MEP-831A Battery Charger Repair & Repair Kits https://www.steelsoldiers.com/showth...83#post2231683
    MEP-831A Remote Start / Governor Controller Kits https://www.steelsoldiers.com/showth...49#post2245549

  2. The Following 4 Users Say Thank You to kloppk For This Useful Post:

    hyderind (09-28-2019), Light in the Dark (11-01-2019), rcamacho (08-23-2019), rpallison (09-05-2019)

  3. #2
    2 Star General
    Join Date
    Jan 2012
    Location
    Massachusetts
    Posts
    617
    Thanks
    56
    Thanked 786 Times in 357 Posts

    Default

    Here is a YouTube video I put together that goes thru virtually all aspects of the Remote Start kit.
    MEP-831A Governor Controller Replacements for the SLC100, 2990-01-477-1371, 98-19539. https://www.steelsoldiers.com/showth...90#post2233190
    MEP-802A/MEP-803A Remote Start Kits
    https://www.steelsoldiers.com/showth...92#post2233192
    MEP-831A Battery Charger Repair & Repair Kits https://www.steelsoldiers.com/showth...83#post2231683
    MEP-831A Remote Start / Governor Controller Kits https://www.steelsoldiers.com/showth...49#post2245549

  4. The Following 6 Users Say Thank You to kloppk For This Useful Post:

    Conatus (09-20-2019), hyderind (09-28-2019), Light in the Dark (11-01-2019), lonesouth (09-12-2019), Sgt Jiggins (09-11-2019), wheelspinner (09-11-2019)

  5. #3
    2 Star General
    Join Date
    Jan 2012
    Location
    Massachusetts
    Posts
    617
    Thanks
    56
    Thanked 786 Times in 357 Posts

    Default

    Bump to prevent deletion
    MEP-831A Governor Controller Replacements for the SLC100, 2990-01-477-1371, 98-19539. https://www.steelsoldiers.com/showth...90#post2233190
    MEP-802A/MEP-803A Remote Start Kits
    https://www.steelsoldiers.com/showth...92#post2233192
    MEP-831A Battery Charger Repair & Repair Kits https://www.steelsoldiers.com/showth...83#post2231683
    MEP-831A Remote Start / Governor Controller Kits https://www.steelsoldiers.com/showth...49#post2245549

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •