• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

What did you do to your deuce this week?

92ramaro

Active member
95
233
33
Location
Memphis MI
Finished replacing the Water Outlet Manifold hoses Friday evening. Spent all night in the mud to ensure readiness for more fire wood shenanigans with no leaks.
The next morning I found quite a bit of fuel in the crankcase so I sidelined her for the day until I could complete my FDC delete this morning.
Fingers crossed on not seeing the oil level rise after this oil change.20191103_142537.jpg

Sent from my SM-G950U using Tapatalk
 

Another Ahab

Well-known member
17,815
4,139
113
Location
Alexandria, VA
Finished replacing the Water Outlet Manifold hoses Friday evening.
That's a fine-looking working rig you got there, 92ramaro, sweet!

A note that gives me shivers though:

- the chain hoist hanging off the bottom chord of that truss might be an accident waiting to happen

I am not so sure that a roofing truss is designed for a point load like that.

The problem is, it's been a long time since my schooling in statics.

Maybe somebody smarter than me (shouldn't take much!), will chime in.



A1.jpg
 
Last edited:

92ramaro

Active member
95
233
33
Location
Memphis MI
"A note that gives me shivers though:

- the chain hoist hanging off the bottom chord of that truss might be an accident waiting to happen

I am not so sure that a roofing truss is designed for loading like that at a single point (the way it's set up)."

That chainfall was hung there years before I was born by the gentleman who had this barn built in the late 80s. I use a skid steer or tractor to pull engines and lift most of the heavy things around here.

I just haven't found a reason to take the chainfall down yet 20191103_144523.jpg

Sent from my SM-G950U using Tapatalk
 

USN_Green_Addict

Active member
Steel Soldiers Supporter
198
84
28
Location
Oahu, Hawaii
Painted and will do vinyl markings this week. I tried to match up the 1960s paint as much as possible. Not sure how it turned out for looking correct.


Sent from my LG-H918 using Tapatalk
 

SCM35A2

Well-known member
Steel Soldiers Supporter
1,974
2,645
113
Location
Florence, SC
Spare wheel/rim is done, exhaust screen cover, air dome cover & misc parts painted. I also removed the damaged rear splash guards. More updates soon...
73458908_2809983835701099_2318335634558681088_n.jpg74819815_2453744948005946_2263512052062486528_n.jpg74604438_2600850219999484_5548828031075745792_n.jpg72715546_630872800650649_4115121987225911296_n.jpg74645253_722061948261058_7270558296942051328_n.jpg76756882_525241544700255_3125906313612099584_n.jpg74674401_415234612749855_1199703963432124416_n.jpg74693539_2521533214561103_3536266700460654592_n.jpg
 

fpchief

Well-known member
1,041
218
63
Location
South Alabama

Ajax MD

Well-known member
1,567
1,414
113
Location
Mayo, MD
Spare wheel/rim is done, exhaust screen cover, air dome cover & misc parts painted. I also removed the damaged rear splash guards. More updates soon...
View attachment 781867View attachment 781872View attachment 781868View attachment 781866View attachment 781869View attachment 781873View attachment 781870View attachment 781871
What are you using for paint and how are you applying it? Are you applying a primer first? What kind?

Also, what do you think about a portable media blaster for removing old paint? Like this:
https://www.harborfreight.com/20-lb-pressurized-abrasive-blaster-68994.html?_br_psugg_q=blaster
 

fasttruck

Well-known member
1,265
622
113
Location
Mesa, AZ
The chainfall is hung from the top cord which is in compression under load but the entire truss is assembled with "pierced steel plates" or gang nails that do not do well under additional unengineered loads. This is a recipe for structural collapse. Suggest an arrangement that does not place the load on the roof be devised. 8 firefighters were lost in a fire of a truss rood building in Hackensack, NJ in 1988 because, among other reasons, there was a significant load on the trusses caused by storage in the truss loft between the lower chord and the roof. Gravity is instantaneous, irresistible and irrevocable.
 

Mrmag1

Head of Stuff N' Things
Steel Soldiers Supporter
602
13
18
Location
Hereford Arizona
I made my deuce short people accessible, set of hunting around for a ladder I decided to get a boat ladder and bolt it onto the gate.

IMG_20191104_154704.jpg
IMG_20191104_154425.jpg
IMG_20191104_154812.jpg

I need to get some longer bolts for two of the four but it holds me just fine.
 

92ramaro

Active member
95
233
33
Location
Memphis MI
The chainfall is hung from the top cord which is in compression under load but the entire truss is assembled with "pierced steel plates" or gang nails that do not do well under additional unengineered loads. This is a recipe for structural collapse. Suggest an arrangement that does not place the load on the roof be devised. 8 firefighters were lost in a fire of a truss rood building in Hackensack, NJ in 1988 because, among other reasons, there was a significant load on the trusses caused by storage in the truss loft between the lower chord and the roof. Gravity is instantaneous, irresistible and irrevocable.
I suppose that the gentleman who hung it was incredibly lucky that he didnt have any structural collapse whilst using it to remove and install engines in customer vehicles back then...

Ran the Deuce after the FDC bypass and had a face that was sore from smiling. Feels like an honest 20HP gain. Between that and rerouting my heater hoses the proper way, along with a new blower motor for the cab heater, I think we're ready for a winter in the woods.
Just need to run it a bit more to confirm I'm not filling the crankcase with fuel through another avenue.
Having a genuine blast with this old iron.

Sent from my SM-G950U using Tapatalk
 

SCM35A2

Well-known member
Steel Soldiers Supporter
1,974
2,645
113
Location
Florence, SC
What are you using for paint and how are you applying it? Are you applying a primer first? What kind?

Also, what do you think about a portable media blaster for removing old paint? Like this:
https://www.harborfreight.com/20-lb-pressurized-abrasive-blaster-68994.html?_br_psugg_q=blaster
I see no issues with that blaster & as for primer I just got some basic spray can automotive primer that is sandable. As for the paint, I used the carc green from
Rapco parts.
 

rustystud

Well-known member
9,071
2,387
113
Location
Woodinville, Washington
What are you using for paint and how are you applying it? Are you applying a primer first? What kind?

Also, what do you think about a portable media blaster for removing old paint? Like this:
https://www.harborfreight.com/20-lb-pressurized-abrasive-blaster-68994.html?_br_psugg_q=blaster
I bought that blaster. It is a pain in the ass to work. Clogs all the time, and goes through media like crazy ! I bought 4 40Ibs bags and they lasted only 1/2 hour. Tried to adjust it to work more efficiently, but it will not work correctly. Only works full on. Plus you need a full protective suit with mask to keep the sand out.
That's why I ended up taking all my wheels to a sand-blaster shop.
 

Ajax MD

Well-known member
1,567
1,414
113
Location
Mayo, MD
I bought that blaster. It is a pain in the ass to work. Clogs all the time, and goes through media like crazy ! I bought 4 40Ibs bags and they lasted only 1/2 hour. Tried to adjust it to work more efficiently, but it will not work correctly. Only works full on. Plus you need a full protective suit with mask to keep the sand out.
That's why I ended up taking all my wheels to a sand-blaster shop.
I wasn't necessarily married to the Harbor Freight brand, I just meant a "portable" blaster. There may be options of a better quality. I can see a respirator mask, but a full body suit? I'm surprised that's necessary.
You're right though, if I can find a shop with a big cabinet for a reasonable price, I'd rather let them do it and save myself the hassle.
 

Mrmag1

Head of Stuff N' Things
Steel Soldiers Supporter
602
13
18
Location
Hereford Arizona

montaillou

Well-known member
Steel Soldiers Supporter
790
787
93
Location
W.WA
So, my deuce is at a shop getting air lockers installed - more detail on this in the thread under Deuce Modifications sub-board. Anyways, while it's there I thought I'd get some other work done, if the price was reasonable (to me).

So, today, they installed an air dryer and alcohol evaporator. Now, I don't know that I'll ever use the evaporator, but it's in the same spot, it cost less than $100 (for the part) and I figure, eh, why not.
IMG_3084[1].jpg
IMG_3083[1].jpg

So, this is on the driver's side, just forward of the middle axle. The mechanic picked this location. I didn't have a strong opinion on location except not in the area where the spare tire & pioneer tool racks were. That spot is reserved for a secondary fuel tank.
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks