• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. lighten

    Cruise Control

    After many PMs on fb, here is what i did for cruise control. You will need CAT ET to configure it correctly. Switches i used came out of a junk freightliner M2 truck and fit good in the square switch holes, but you need a on/off and a 3 position momentary switch. Also need 3 pins to plug in...
  2. lighten

    7 ton MTVR Parts Reference Spreadsheet

    I think its either napa # 25120964 or 25120945. One is 97" and the other is 95".
  3. lighten

    7 ton MTVR Parts Reference Spreadsheet

    Wiper arms, Mack truck # 82281459. Comes with washer nozzle and hose, uses regular automotive wiper. Battery box rubber hold downs, Napa # WJ195. Little smaller than factory but they work. Water/fuel seperator, Napa # 3838. Longer, better micron rating and gets rid of the pos screw on plastic...
  4. lighten

    7 ton MTVR Parts Reference Spreadsheet

    I think the part number your looking for is Airsource # 1513 binary switch, this switch has low press and high press on/offs in the same switch. The green switch is the engine fan switch, Air source # 1446.
  5. lighten

    MK 23 Ac kit instructions

    so Had 2 wires not in the correct spots in on the ford switch. Thanks for the info
  6. lighten

    MK 23 Ac kit instructions

    I gotcha, text sent
  7. lighten

    MK 23 Ac kit instructions

    Need freon charge capacity and what wire numbers need to go in what pins on the ecm? Does the ecm need to be configured in any special way using cat et?
  8. lighten

    MK 23 Ac kit instructions

    Does any one have a copy of the instructions for the ac kit in the MK23s. Just purchased a truck and previous owner installed the kit, looking to make sure wiring is correct before i start tearing into it more. Thanks
  9. lighten

    CTIS - Blowing oil

    So i have some hub seal problems? It only blows air out said tubes when deflating the tires. One would think it would do it when inflating also, i dont think it does inflating then. I have never had a hub apart so i may be wrong?
  10. lighten

    CTIS - Blowing oil

    Where is the CTIS suppose to dump air when it is deflating the tires? I have seen air come out the same hose as the #1 post picture by radiator, and also out of a large tube behind the cab by the trans fill tube were other vents are. Is this correct operation?
  11. lighten

    Wrecker bed modification

    You probably could but it may be in the hood, I didnt try it
  12. lighten

    PT Pump Adjustments

    Ill see if i can get one this week. They are almost the same turbo but the ht is a updated version, exhaust housing options, flows about 300cfm more air and the compressor outlet is v-band. I have used the 3b numerous times for cheap 12v twin turbo builds, they make good power for what they are.
  13. lighten

    PT Pump Adjustments

    Yea sounds like a need a button also. I added a HT60 turbo and then checked my rail pressure. My rebuilt pump had about 165 psi, with a 32 button. I adjusted it at the throttle shaft to 195, throttle response is better, but only 800egt @15 psi boost max no smoke at all. I think iam gonna go...
  14. lighten

    PT Pump Adjustments

    Also interested in this. What fuel button did you use?
  15. lighten

    Wrecker bed modification

    Added a turbo today. Need to play with the pump some, has a #32 button in it, only about 700* max pre turbo egt.
  16. lighten

    Wrecker bed modification

    This is what i started with. Mainly used for pulling out farm equipment, used the rear pto winch for a while until i cracked the housing on it, winch cable broke while pulling out a 60k lb cotton picker buried to the axles. Ripped everything off that was not needed put a hyd 45k winch on the...
  17. lighten

    Wrecker bed modification

    Just needs a turbo
  18. lighten

    M816 Hydraulic Pump

    Ok, if my guy doesn’t come thru i will be in contact
  19. lighten

    M816 Hydraulic Pump

    Got the DP 55k winch mounted waiting on another tank and pump
  20. lighten

    M816 Hydraulic Pump

    ] I installed DP 45k hydro winch in the old winch location, iam gonna use the tank from the winch and valves. I have a 2 stage hydro pump ordered that will flow enough to run 2 winches, winch i plan on putting another 45k in the crane location, if any one has a DP45k winch around south GA let me...
Top