• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. S

    LMTV CTIS UPGRADE

    Right forgot. If Depo's or DLA buy the kits I am sure they issue a number but it is too early yet.
  2. S

    LMTV CTIS UPGRADE

    This is a good question. The selling entity would need to have an account set up with Dana Crossville Aftermarket the same as a truck parts distributer. I do know that every hand that touches a part increases the cost so maybe someone on this site has access to an account.
  3. S

    LMTV CTIS UPGRADE

    No they do not sell separate sub-components What is an NSN?
  4. S

    LMTV CTIS UPGRADE

    There is now a CTIS Wheel valve rebuild kit that will be sold through Dana Aftermarket but they will need to see orders before they will build and stock them. Unfortunately I do not have the SRP yet. The kit includes a new diaphragm that will not fail in the cold or cause corrosion. It also...
  5. S

    LMTV CTIS UPGRADE

    The kit is now in the Dana Aftermarket system but they will need to see orders before they will build and stock them. Unfortunately I do not have the SRP yet. The kit includes a new diaphragm that will not fail in the cold or cause corrosion. This includes a vented cover and protective bracket...
  6. S

    LMTV CTIS Question

    Yes it started on the A1P2
  7. S

    LMTV CTIS Question

    They are threaded. I did not want to include the seat as the kit without the seat would service 10 or so part number wheel valves, with the seat it would only be specific to one or two valves. I can check about making the seat available for LMTV/FMTV
  8. S

    LMTV CTIS Question

    Hello Everyone, I have run into a holdup on the updated wheel valve release so I am perusing a rebuild kit instead. This kit would include a vented cover and protective bracket, new diaphragm good for -30F operation, and screws. The seat and spring would be your responsibility to clean and...
  9. S

    LMTV CTIS Question

    Please keep in mind that software configurations set by the ECU pins M and Z also set fault tolerances for a specific chassis. Selecting an incorrect config could cause pressure reading to be inaccurate, over inflations, or even a flashing light fault to occur. S&S and later models are all wired...
  10. S

    LMTV CTIS Question

    https://www.steelsoldiers.com/threads/spicer-ctis-trouble-shooting-guide.195064/
  11. S

    LMTV CTIS Question

    AXTS0015 Troubleshooting Guide
  12. S

    LMTV CTIS Question

    You can disable the ECU by interrupting the PS Pressure Switch signal or put a 5 amp switch in line with the 24v power wire. The ECU had protections against power surges and very robust. Welding on the chassis with the vehicle power on can cause issues but not jump starting.
  13. S

    LMTV CTIS Question

    The only light for CTIS on the dash is the overspeed warning light. It should flash if the truck speed is exceeding the limit for the tire pressures and be on solid if the speed signal is no longer present after 50 key cycles. It will turn off as soon as the ECU sees a speed signal. Attaching a...
  14. S

    LMTV CTIS Question

    Most Trucks that have a CTIS disable switch for an arctic kit use the pressure switch wire. This way is can be disabled before start up and easily engaged after running down the road and the seals are warmed up. Take either with at the the switch, cut and splice two wires, then run them up to a...
  15. S

    LMTV CTIS Question

    Old wheel valves can be a problem and they will perform worse when it is colder out. Just take it apart and clean everything good. Remove any corrosion from the stainless seat and use a lightweight oil to soften the rubber diaphragm.
  16. S

    LMTV CTIS Question

    The PCU will handle 140 PSI so it is not a problem. When using switched you have inflating is easy, just turn on "Control" then "Supply" and air will flow into the tires if the supply is higher than the tires. NOTE* If the supply is lower than the tires, the tires will deflate down to the...
  17. S

    LMTV CTIS Question

    You do not need the ECU to control the system. There is a switch box diagram on one of the other posts. The PCU has the deflation relief valve that controls the line pressure at 8psi allowing the wheel valves to dump. You also do not want to turn on "supply" without turning on the "control"...
  18. S

    LMTV CTIS Question

    Sounds like the switch is bad. You could take the metal bezel off and use a razor knife to cut around 3 sides of the button then peel the cover back and see if you can clean the contacts. The metal dome will come out and you could use a metal clip to short the contact and make sure they work. If...
  19. S

    M923A2 CTIS Problem

    Great to hear, we hope to have some better wheel valve parts coming soon that will solve the old cold temperature issues.
  20. S

    M939 CTIS Reprogram, Anybody Done It?

    Some green modules after 1998 can communicate with the tool on a J1587 link. All black modules should be able to use a CAN link.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks