Tab Content
  • TGP (IL)'s Avatar
    Yesterday, 18:21
    TGP (IL) replied to a thread M1008 or 1028 rattle in CUCV
    Fuel tank skid plate Tom
    5 replies | 102 view(s)
  • TGP (IL)'s Avatar
    06-22-2019, 18:40
    TGP (IL) replied to a thread M1028 Dana 70hd pinion yoke in CUCV
    You need proper tools, As far as Yoke removal you will need puller. Tom
    17 replies | 340 view(s)
  • TGP (IL)'s Avatar
    06-22-2019, 18:37
    TGP (IL) replied to a thread M1028 relay identification in CUCV
    The three relays on the plate under dash are 1 Starter 2 Volt meter 3 Gen 2 charging relay Tom
    5 replies | 117 view(s)
  • TGP (IL)'s Avatar
    06-21-2019, 10:08
    Google vintage truck glove box bumpers. Most of vintage cars and trucks used varying types on glove box doors. Tom
    6 replies | 198 view(s)
  • TGP (IL)'s Avatar
    06-19-2019, 20:47
    TGP (IL) replied to a thread Fuel Line Help in CUCV
    I don't have a part number, but this link might help identify it. https://www.clagrills.com/grillpartshelp/glossary/flare-fitting.htm It's 3/8...
    11 replies | 192 view(s)
  • TGP (IL)'s Avatar
    06-14-2019, 17:17
    You need to determine if it is algae or bio diesel separation from old fuel. Of course if your not using bio blend or the fuel is relatively fresh,...
    9 replies | 353 view(s)
  • TGP (IL)'s Avatar
    06-11-2019, 21:33
    TGP (IL) replied to a thread Over heating in The Deuce
    "I put a hose in the top and it runs out the bottom but does fill all the way back up to the top. The bottom flows well but might have some Plugged...
    8 replies | 130 view(s)
  • TGP (IL)'s Avatar
    06-11-2019, 20:16
    TGP (IL) replied to a thread Over heating in The Deuce
    My M35 will run at 160 all day long until you work it hard then it will reach 180,and then The T-stat opens and the temp comes right down again. ...
    8 replies | 130 view(s)
  • TGP (IL)'s Avatar
    06-11-2019, 17:19
    TGP (IL) replied to a thread Strange parts in M37
    None of those parts are for a m37 that I can tell. Does appear to be a winch PTO drive shaft, bit for what? Tom
    3 replies | 158 view(s)
  • TGP (IL)'s Avatar
    06-04-2019, 21:53
    TGP (IL) replied to a thread Coil test in M38, M38A1 and M170
    See if this will help. Click the image, then click it again Tom
    3 replies | 184 view(s)
  • TGP (IL)'s Avatar
    06-03-2019, 19:05
    TGP (IL) replied to a thread Alternator question in CUCV
    No should not sound like that. Also sounds dry with bearing rumble. And the rear bearing is not a bushing, i'ts a caged needle bearing. Complete...
    10 replies | 286 view(s)
No More Results
About TGP (IL)

Basic Information

Age
66
About TGP (IL)
Location:
Metro East IL
Interests:
Old trucks and equip.
Occupation:
Retired Heavy Equipment operator/Master Mechanic

Signature


"99" Durango
"99" Dodge 3500 CTD Dually
"86" Chev M1028A2 Dually
"84" Chev K 30 6BTA,400 3.73,No-Spin
"77" Chev K 30 400ci 400,4.56, No-Spin
"65" Kaiser M35A1 WW
"54" Willys M38A1
"52" Dodge M37 WW
"47" Dodge WDX WW
My Photo Album http://www.t137.com/cpg/index.php?cat=10010

Statistics


Total Posts
Total Posts
461
Posts Per Day
0.14
Total Thanks
Total Thanks
1,351
General Information
Last Activity
Today 22:23
Join Date
09-11-2010
Referrals
0
Home Page
http://www.t137.com/cpg/index.php?cat=10010
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
1
100.0%
Members who left positive:
Members who left negative:
1
0
Total positive feedback: 1
Submit Feedback For TGP (IL)
View Complete Feedbacks for TGP (IL)
  Past
Month
Past
6 Months
Past
12 Months
  0 1 1
  0 0 0
  0 0 0