Tab Content
  • Slate's Avatar
    08-17-2019, 17:53
    Slate replied to a thread M35A2 Transmission in The Deuce
    So tranny flushed cleaned new oil and man she feels good. New clutch and main seal. No Leaks. Need to find parts and a rebuilt transmission or NOS...
    9 replies | 266 view(s)
  • Slate's Avatar
    08-15-2019, 11:02
    Slate replied to a thread M35A2 Transmission in The Deuce
    Anyone ever heard Charlie Robinson. Loving County? "Like a thousand tiny diamonds in the lights of Loving County". That's what my pretty oil looked...
    9 replies | 266 view(s)
  • Slate's Avatar
    08-15-2019, 09:25
    Slate replied to a thread Metal in transmission in The Deuce
    Ha no sawdust please I've got plenty. Cutting wood for winter in 100F. No central heat or air. I bought a truck from a guy that had put sawdust in...
    38 replies | 1060 view(s)
  • Slate's Avatar
    08-15-2019, 09:02
    Slate replied to a thread Metal in transmission in The Deuce
    Thank you sir. I was going to clean out pieces and fill the transmission back up with this and run it. But I may take the time and fix it right. ...
    38 replies | 1060 view(s)
  • Slate's Avatar
    08-14-2019, 20:30
    I need to rebuild my transmission in my M35A2. Looking for a good one to replace or to get parts from. In Texas preferably Sent from my moto z3...
    0 replies | 90 view(s)
  • Slate's Avatar
    08-14-2019, 17:01
    Slate replied to a thread M35A2 Transmission in The Deuce
    I have a full gasket kit. And yes It shifts better than my other 2 trucks. I'm just to a point I have basically built this truck over the last...
    9 replies | 266 view(s)
  • Slate's Avatar
    08-14-2019, 15:25
    Slate replied to a thread Metal in transmission in The Deuce
    So found this in my garage from 2006. GL5 GL4 Mil-L-2105-D says Spicer. Would this work for tranny? Be nice to use some crap I have laying around....
    38 replies | 1060 view(s)
  • Slate's Avatar
    08-14-2019, 12:53
    Slate started a thread M35A2 Transmission in The Deuce
    Replace gears or clean up pieces and change oil and run? Sent from my moto z3 using Tapatalk
    9 replies | 266 view(s)
  • Slate's Avatar
    08-14-2019, 09:52
    If gasket is needed can I make it out of this? Sent from my moto z3 using Tapatalk
    28 replies | 465 view(s)
  • Slate's Avatar
    08-14-2019, 09:49
    As I am new to this I need some advice. The bolts to this seal housing came out with almost no force. Meaning they were more or less loose. There...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-13-2019, 23:06
    Checked oil level today and yes even though I seem to loose quite a bit of oil after running. My oil level is increasing not decreasing. Fuel in...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-13-2019, 15:45
    Yes Sir thank you. There is a slight white chalk mark left above one bolt hole. I did read enough to mark it because of the "only one way" it goes...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-13-2019, 14:35
    Another it does look better than the mirror finish it had. Sent from my moto z3 using Tapatalk
    28 replies | 465 view(s)
  • Slate's Avatar
    08-13-2019, 14:15
    Cleaned up best he could. Said unless I'm going to NASCAR the cracks shouldn't be any issue. I'll keep an eye out for a spare for down the road. ...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-13-2019, 12:11
    I have changed clutches before on pickups but never rear main seal. May be a dumb question but. Do I need to drain oil before taking seal out? ...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-13-2019, 09:17
    Thank you sir. I should find out today. Did find a crack from surface to inside middle of inner lip. How do you feel about bypassing FDC on these...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-12-2019, 23:11
    FDC was never bypassed. I can run my truck to town and back with no leaks but when I turn it off I get a puddle from oil pouring out like it was...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-12-2019, 22:25
    I would venture to guess rear main is out as well. Sent from my moto z3 using Tapatalk
    28 replies | 465 view(s)
  • Slate's Avatar
    08-12-2019, 21:06
    Pilot.... thank you for your patience with me. I will take my flywheel to a machinist tomorrow to see if it can be turned. How much is too much in...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-12-2019, 20:50
    Reason I was asking about bearing is this TM pic saying throwout Bering behind clutch plate. The plate in this pic is the new one I have. Old one...
    28 replies | 465 view(s)
  • Slate's Avatar
    08-12-2019, 20:44
    Understood thank you. Sent from my moto z3 using Tapatalk
    28 replies | 465 view(s)
  • Slate's Avatar
    08-12-2019, 20:43
    Lots of cracking in flywheel I was in the process of changing main seal. I ordered a clutch kit from C&C for a deuce but the clutch plate sent is...
    28 replies | 465 view(s)
More Activity
About Slate

Basic Information

Age
41
About Slate
Location:
Ozona Texas
Interests:
Small ranch in West Texas. since I found my first multifuel, 5 ton, Ive been hooked. recently added
Occupation:
Self employed rancher, and Groundwater District Manager
MVPA:
MVPA?

Statistics


Total Posts
Total Posts
238
Posts Per Day
1.78
Total Thanks
Total Thanks
128
General Information
Last Activity
Yesterday 20:16
Join Date
04-09-2019
Referrals
0
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For Slate
View Complete Feedbacks for Slate
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0