Tab Content
  • Daves86's Avatar
    Today, 21:41
    Well, testing proved the solenoids were shot as well. Putting 24v to motor terminals drives the motor which moved the main shaft to turn the winch...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    11-09-2019, 22:47
    Got the 2 drum bushings and the gear housing bushing replaced and got the electric motor installed today. Hope to have it all done this weekend
    38 replies | 1331 view(s)
  • Daves86's Avatar
    11-05-2019, 22:30
    Found what was stopping the free spool. Not the rust marks on the shaft that coincide with where the drum bushings sit The end with the darker band...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    11-02-2019, 20:53
    New motor has not showed up yet. Pulling this apart because it does not free spool. I think the drum is seized to the shaft. If the drum turns so...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    11-01-2019, 20:53
    Thanks Coug! Hammer and chisel got the key out. Still cannot get the drum off the shaft. Tried removing the cable and bouncing the shaft end on...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    10-31-2019, 21:32
    Anybody know how to separate the drum from the shaft? This key is staked and the ends are forked to not come out of the shaft key way. It is now I...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    10-30-2019, 22:21
    Found where the water came in Should not see light thru a mounting hole. Fixed with JB weld. Still working on getting the drum removed, it is...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    10-28-2019, 12:58
    Hadn't thought about soaking the motor. I ordered one last night (and gasket set with oil seal for the motor) less than $500 which meets my rebuild...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    10-27-2019, 20:11
    Hadn't thought about a second winch. Let's see if this repair works. Here is where the water was Here is where the water wasn't This is a stuck...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    10-26-2019, 22:39
    Well I got the winch pulled after draining the fluids I did say fluids (water in the lube) the real fun was not seeing these screws because someone...
    38 replies | 1331 view(s)
  • Daves86's Avatar
    10-24-2019, 16:19
    Daves86 replied to a thread Temperature gauge issues? in HMMWV
    My 86 gauge would be fine then start bouncing 200 to 240. I changed both the meter and the sending unit to no avail. For mine I had to install the...
    3 replies | 100 view(s)
No More Results
About Daves86

Basic Information

Age
54
About Daves86
Location:
Manassas/VA

Signature


M998 Basic
Dave

Statistics


Total Posts
Total Posts
41
Posts Per Day
0.29
Total Thanks
Total Thanks
16
General Information
Last Activity
Today 21:44
Join Date
07-03-2019
Referrals
0
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For Daves86
View Complete Feedbacks for Daves86
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0