Recent content by BlackhawkMTP

  1. B

    MEP-002a fuel pump issue?

    I haven't read the TM's for this generator yet. Thanks for your response and explanation of how those fuel pumps operate. It just sounded odd switching between the AUX pump which sounded like a normal fuel pump to me with the humming noise the switching to the main pumps with the relay clicking...
  2. B

    MEP-002a fuel pump issue?

    It has a three pin connector on the pump. A,B,C pin. Do I check A,C and B,C with my multi-meter?
  3. B

    MEP-002a fuel pump issue?

    So on my MEP-002a generator I am turning the start switch to "Prime Run AUX" and I get a normal sound of a fuel pump running. When I switch it to the next clockwise position of "Prime Run" I don't hear a fuel pump running and I hear what sounds like a relay clicking? I am trying to figure out...
  4. B

    Glow plugs for MEP-002a/MEP-003a

    I didn't know that. Thanks for clarifying. Where would the other installation position be if they aren't installed in the air intake? Nevermind, I found it in the cylinder head drawing.
  5. B

    Glow plugs for MEP-002a/MEP-003a

    The MEP-002a parts manual says it take Champion 49 glow plugs. Is this a misprint?
  6. B

    MEP-002a spin on fuel filters

    Okay sound great, thank you. I didn't know if I should get 1/4 inch or 3/8 inch thick.
  7. B

    MEP-002a spin on fuel filters

    What size aluminum stock did you use for the mounting plate? Nice setup, I plan on doing the same thing!
  8. B

    MEP 002A and 003A

    Is there anyway to reference the articles linked in Post #1 of this thread again? When I click on the links it seems like the website has deleted the thread due to old content or something. I believe this is very good information contained in here as I have recently bought 2 MEP-002a generators...
  9. B

    Mep-802a glow plug source?

    Attached is the picture of the box. They are that part number so I assume they will work. This is the part number that they had in the TM that I looked at. I just didn't know if they made a 12v and a 24v version or if maybe they were 12v in series to create the 24v?
  10. B

    Mep-802a glow plug source?

    I bought some off the big auction site with this same exact part number and noticed that they say 12v on the box after I ordered it. Will it work in the 24v system?
  11. B

    MEP-802a House hookup

    The Plug does have pins in it, I didn't think about that. Can't they be swapped around? I think I remembered a thread where someone on this site said they could because they had the same issue with their plug.
  12. B

    MEP-802a House hookup

    More than likely a few days other than if I find myself on vacation somewhere for a week or two. Another quick question that I'm sure has been covered here extensively before but what are some good parts to have on hand other than the obvious oil and fuel filters, and serpentine belt? I know...
  13. B

    MEP-802a House hookup

    That makes a lot of sense. I guess I never really thought about it that way because I knew I would be there if something went wrong. I got tunnel vision on what if this happens when I'm gone but you're right. Nothing is going to be on that the MEP-802a can't handle while I'm away. I have a...
  14. B

    MEP-802a House hookup

    I should have probably just installed the 60 amp SCAME plug from the start instead of the 30amp. I was thinking that they had to be sized for the generator but what you said makes sense. Thanks for the explanation.
  15. B

    MEP-802a House hookup

    Thanks Coug! I will give PSP Products a call today so that I can inquire about their 100 amp load shed box and it's capabilities. I would like to eventually get a MEP-803a also. I would like to have two separate plugs mounted under my Kohler ATS. The one that is currently mounted there and...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks