• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Recent content by JoeydHMMWV

  1. J

    Glowplugs..... and the "AFTER GLOW"

    Ok I have a 1994 M998 it has a NARTRON PCB and GP Controller. It has an intermittent issue below -5 degrees F (-20C) I THINK it is the Glow Plug controller but the way the TM reads it says it is the PCB but the TM really does not address intermittent problems. The truck ALWAYS STARTS the...
  2. J

    What have you done to your HMMWV today/lately

    Dinked around today and removed the military radio rack so I could change the two bad glowplugs on the passenger side.
  3. J

    Thunder Over Michigan 2016 - Humvees Wanted!

    So did you guys get all the hummers you wanted for the show?? Never heard anything either via PM or in this forum.
  4. J

    WD40 paint refresh

    My preferred parade finish is to spray it with water and drive another vehicle around my dirt driveway and generate dust to give it that desert fresh patina
  5. J

    Engine Color HMMWV

    My question revolved around some 6.2 heads I got, they were what I thought was GM Corp Blue but come to find out the actual color was GM Diesel Green after some talking to a buddy that worked for Detroit Diesel the military stuff / American General stuff was shipped from Detroit Diesel Black...
  6. J

    Engine Color HMMWV

    Did GM use anything other than black for the 6.2 diesel on the HMMWV??? Specifically did they use GM Corporate Blue??? I have a ton of it and I have to replace Both cylinder heads on one of the beasts I purchased and though I would do a "DUPONT" rebuild on the bottom end... I guess I can...
  7. J

    PCB EESS Starting issue.

    Oh yea!! This does bypass every safety in the book it starts the motor and does not care if the truck is in gear. My rewire of the PCB (Ain't paying for a Rebuit or new one) will include the Neutral safety circuit but will bypass the glow plug circuit Having had more than one diesel I think I...
  8. J

    PCB EESS Starting issue.

    The fuel solenoid stays to hot until you want to shutdown then disconnect.
  9. J

    PCB EESS Starting issue.

    REMOVE Wire 54A from the Fuel SOLENOID then connect the Fuel SOLENOID directly to the positive Battery terminal. Rock and Roll!!!! (Hit Start) Depending on how cold the motor is you may want to connect the advance solenoid (Wire will be marked 569) remove it and wire the ADVANCE solenoid to...
  10. J

    PCB EESS Starting issue.

    Yes it possible the battery grounded out as it was not bolted down. On a "POSITIVE" note the glow plugs were removed and checked they are all good (the system is not cycling them) nor is it engaging the Fuel valve, or Cold Advance everything else lights ect are all working. When the fuel valve...
  11. J

    PCB EESS Starting issue.

    My M998 came Thursday batteries were dead on the carrier we tried to jump it and we ended up using the Backhoe to pull it off the truck. I put a set of CAT batteries in it and it started up ran fine shut down fine and have been playing with it all weekend no issues. Today went to start it and...
  12. J

    Thunder Over Michigan 2016 - Humvees Wanted!

    My Mother-in-law lives by Willow run.. My toy. ~~
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks