• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Ray70's latest activity

  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    Once you get the linage sorted out, if the issue remains, refer back to post #8 I still think you should verify the governor droop...
  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    You guys are misunderstanding how that lever works. It's not part of the governor control system, it's the fuel on/off lever and only...
  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    I'm not following you... The FSS linkage doesn't move along with the governor / rack during operation, all it does is pull the "stop"...
  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    It probably has no effect related to his problem, but you're right, something is wrong with the way the FSS arm is bolted on. Should be...
  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    Just a couple more questions, was there a load on the generator in the beginning of the video? If so, how much? The load meter was...
  • R
    Ray70 replied to the thread MEP003A frequency meter in-op.
    Look at the face of the meter, I believe the lower right side, you should see something that says FS XXXXX That will tell you what the...
  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    I'm hoping that by "Idle" you mean running at operating speed, but at no load? That is fairly Typical of a machine with an oversensitive...
  • R
    Ray70 replied to the thread MEP803a Rough Idle.
    Very strange, it sounds like it's surging rapidly, like the governor droop setting is too sensitive, but I don't really see any swing on...
  • R
    Ray70 replied to the thread MEP003A frequency meter in-op.
    Rick, FYI the one LITD linked to above is the same one I had mentioned in my P.M. I've used a few of them in the past, you just need to...
  • R
    Ray70 replied to the thread Buying MEP-803A - Good Deal?.
    Even if it didn't run it would still be worth way more than the asking price!
  • R
    Ray70 reacted to Guyfang's post in the thread Mep 802A with Like Like.
    Hello I have an 802A I recently acquired and it seems to run decent but there is a lot of fuel I guess all over the engine compartment...
  • R
    Ray70 replied to the thread Mep 802A.
    Agreed... I had one that looked like he got dropped on the leg and shattered the cast iron plate with the thread in it. My only option...
  • R
    Ray70 replied to the thread MEP-802.
    In that case you hammer action had to have done something else to "fix" a bad connection somewhere. The fuel level sensor has absolutely...
  • R
    Ray70 replied to the thread Mep 802A.
    You will find a lot of posts on here about crankcase pressure, especially on the 802 where people think they have pressure based on...
  • R
    Ray70 replied to the thread Mep 803A.
    Off hand I don't recall if that is a 1/4 NPT or a 3/8" NPT thread, but it's one or the other. Probably 1/4" NPT I'd bet. If you look...
Show older items
108,769members
163,965threads
2,306,860posts
399online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks