Recent content by s4mm4n16

Thanks, I thought they where the same size, just wasn't sure. I'll try it today. My second winch is going to be a problem. Every plug, set screw and a few shafts are frozen. Pretty annoying. I have the same problems with the yoke shaft being stuck. It's rusted on the inside and I'm sure will...

I have pushed out one side and the other bearing is still hanging inside the case on the other end of the worm. That is the one I am trying to get out the other side of the case. I will remove the bearings from the worm with a press when I get it out of the case

OH, I might add that the clanking noise/bell noise is similar to hitting the e-brake drum or a drive shaft. It transfers thoroughout the entire drivetrain and can be very confusing. Had me thinking trany, transfercase or other major components. My clanking must have come from the wind up of the...

Sorry for not getting back to everyone. I found the problem to be the clutch disc. The one I had in had no springs around the hub. The new one does. Problem solved, as I guessed they kind of act like a shock absorber. This is a air shift truck. The e-brake may have been contributing also. I...

10/4, I was extremely happy to NOT hear the noise after having the trany out 4 times. Now i'm going forward with installing a winch. Found out that it did not have the drum seal on one side. Got that appart now. It's amazing that a GOV. rebuild would have had this part missing. Thanks for...

Everything is out of the case. Drum shaft and gear...Everything. All that is left is the worm gear with the bearing on either end. I have driven the assembly out of the case to the front of the winch, as stated in tha manual and I am trying to get the second bearing to pass thru the opposite...

Hello, I have been following this thread and am rebuilding 2 winches myself. I have one almost apart and I am trying to get the worm gear out with the bearings on the either end (drum shaft is out). I'm useing TM9-2320-209-2-3 on page 18-9, frame 8, with explanation. I have driven the 1st...

Well, i finally got the time to figure out the problem and it was the clutch disc. Tried another with the springs and it works great. Reduced the noise almost completely. Just thought I would close this chapter/thread. Thanks for all the input.

I'm kind of on hold right now, but I will try to update. One of the first to respond to my inquiry asked what the lube looked like and I can't answer that, because I didn't pay attention to it, but I will the next time. I think the bearing is OK but I'm ordering another new one to put that to...

That is how I have adjusted the clutch linkage before. My best guess is the E brake or the disc. I don't think it is the throw out beaing. Waiting on a new disc to try that.

Here is the explanation I wrote before in another thread. Also, thanks to all for trying to help. I've put clutches in the M35 before, so I don't think I have the disc in backwards and all the clutch parts are new. I'm driving forward, or in reverse, about 100 ft. on hard pan road, using 1st...

On the second page here in the forum, I have a thread titled "Noise in the drive train". In that I tried to describe the problem as best as possible. I didn't get a bunch of responses, so I tried to ask my questions in a different way with this thread. Also, I am new at this site and I am having...

I have been trying to figure out where my drive train noises are coming from so hopefully someone can help. I have pulled out the trany again and I can find nothing wrong with my disc and pressure plate. Both are new. A couple of guys are saying the throw out bearing is bad and I thought the one...

Hello, I tried all of the suggestions I received and a few other things. Backed off the E brake, checked shafts and universals and I still have the noise and I don't like the sound of it. Tomorrow I drop the trany and check my clutch/installation and see if I can find a problem in the...

Hello, the t/o bearing is new and greased. I ran the engine with the trany bolted up without the short shaft in first, just to make sure there was no strange noise's before finishing. Standing still with everything running and installed, there is no noise. It's when I am coasting between shifts...