Search results

I’ve got hot engine air coming up through the small slot on the parking brake. Is there a way to insulate that? Any suggestions would be appreciated.

Is there a rubber seal or grommet that goes in the hole that the wiring from the front blackout light goes through? I've looked through the Parts and Tools Manual and I am coming up with nothing.

I had an issue this morning where I put my HMMWV in drive and it wouldn’t engage. Same with reverse. It finally did after a little back and forth. It was unusually cold today and I was wondering if I just need to let it warm up longer to not have this issue.

Does anyone have any good suggestions for a mounted holster for an 87 M998? All the ones I find are magnets and that’s a no go for aluminum.

I’m running into an issue and I’m wondering if anyone else has experienced this. If I park my 87 M998 on an incline overnight occasionally in the morning the transmission will not shift into reverse or drive unless I go back and forth a few times between the two. I have good fluid levels and...

My power steering pump has been wrrrrrrrring. In the morning when it’s cold it doesn’t do it. But after it warms up it starts making noise. Also when it’s cold (before starting) the fluid level is fine but if I check it after I drive a few miles the dipstick is bone dry. Is this a big issue or...

I just got a stereo system installed in my M998 with a console, rear speakers, sub and amp. When I went to pick it up the shop told me that the converter that I supplied wasn't working because it was adjustable and the amp required a constant 12v converter. I have the Orion 2412-70a. Does...

I searched the threads and I couldn’t find info on this so I guess I’ll ask. Is there a way to adjust the sensitivity of the break light? I have to really press down hard on my break pedal to get the lights to react. Any help would be appreciated.

I have one of the directional switches that have the green light on it that is supposed to blink when the blinkers are blinking. I replaced the bulb with an LED but it still doesn't work. I'm not sure if I have twisted the LED enough to make a full circuit and since i have fingers like a...

I have an 87 M998 6.2L. I'm trying to find the 3 info plates that should be on the front of it but I'm coming up with nothing. Does anyone have any suggestions on where to get these? Any info would be greatly appreciated.

Here’s a fun question. I went to an exhaust place to get my exhaust fixed. It turns out that one of the reasons that it was so loud in the cab was because the exhaust wasn’t connected. The guy fixed it and it’s much more quiet. My question is would this make my engine run cooler? (It is).

Quick question- I’m installing a new soft top and I’m running into trouble. How do you get this part in that part? I’m running out of options.

Im having an issue with some 24 v LED headlights. the drivers side works fine on HIs and LOs but the other one wont turn on at all. I also swapped out the marker lights that had the ground on them. These just have a little metal ring on one of the screw holes and I'm not sure how that would...

I’m installing a fording exhaust and I’m having an issue with what gasket to use. When I look it up sometimes it says flange. Other times it says donut. Which is the right one? Any help would be appreciated.

I'm having trouble finding a place that can mount stock tires on the stock rims. They all say that their machine isn't big enough to balance them. Any suggestions where to take them to get this done?

I'm going to be putting a piece of 3/4 in plywood down on the tunnel to help with the sound insulation. I'm going to use self tapping screws. Before I make any colossal mistakes what is the clearance under the tunnel? I know the fuel tank is under there and I don't want to puncture it.

Is there a better set up than the round knob for the hard door latch? I keep slashing my knuckles when I open my door from the inside.

I’ve seen some pics of engines that have 2 fans mounted on the radiator. Is that for an AC unit or is that to help cool? If it is to help cool does it work well?

I have a question about temperature. I have a 1987 M998. It runs around 220 degrees. Some people I've talked to say that that's fine because the older ones ran hot. Some people say that I'm going to blow the head gasket. The gauge is accurate. I did an infrared temp at the thermostat. Any...

Does anyone know of any shops in the Tampa,FL area that installs AC units in M998s? I’m looking to get a red dot system put in.