Search results

I built a m923a2 that I bobbed with air ride and set up real nice, that truck I miss as it was smooth and had power. My m925a1 i do not really miss. I really like the m1078 but torn betwen the bobbed 5 and the 1078. I plan on keeping my 1078 as it is more versitlie, tons more cab room, 4x4 takes...

Turned up with no load in the truck she will continue to pull hills and not downshift. Ive seen 1200deg and rising allowing it to do its thing will lead to meltdown. ive then had 8000lbs in the bed and it will pull similarly but much happier. My point was if one is so inclined to dive into the...

Ill try to get my sources of info up. They make the special tooling due to tight working conditions and fine adjusments. If you had to res6nc the rack then you are either forced to buy the kit or take the entire intake manifold and valve body apart to wo4k through it. I made very minor...

Huck bolt. Had a 1" gun strip one off to see if it was even possible. Highly do not recommend, cut off with a cut off disk or a torch and replace with grade 8 and torque

http://www.steelsoldiers.com/showthread.php?137555-m1078-list-of-mods/page2 post 19

What would the price point be? Air actuated?

Cut a hitch on my plasma table and mounted it up. Got a 6 pin to 7 pin whip and will mount that in as well. Ill likely wire in a brake controller as well. Possibly putting a gooseneck hitch on as well

I know ajaco in Parsippany hauled back a few for Harrison dpw and a few other towns.

Followed the procedure for the cat 3116 to set valves, adjust injectors and advance them. Turned up the fuel and air ratio and she hauls. 9ulls hills without downshifting which causes egts to climb. Overall its much nicer now to notnhave to work the peddle for power. Building the hitch this week

MidnightDuramax. just did Added a pyro last weekend, plan on setting the valves and resetting/advancing the injectors and turning up the motor this weekend or in the next week once I get some good baseline numbers on egts to see where I am running currently. I am also hoping to get time this...

383 green and the black. HD 4300 base. Used an airless sprayer and used the hf hvlp gun for ffine tuning

Gears work great. Now to balance the wheels when running above 55. Gears are 3.07:1. Roof rack Iis bolted to the roof with nutserts. Now looking to put in a pyro and open her up a little. I am not sure what you mean by defroster plenumn. Its open across the windshild. I do need a new speed...

How did you go about balancing the wheels? Did you counter balance the ctis puck like the m939a2 trucks do? Remove the runflat and put dynabeads in?

I also had an issue with a few memebers on a power trip and poor attitudes but ill leave it at that. I didnt bring 3 vehicles up to be called a liar. I was planning on attending with the same three and something else sunday but yard work became more appealing vs the hassle. If there all these...

Ajaco towing in Parsippany nj runs down there for Harrison on Kearny town pickups

Along those, lines its really tight in the rear to do some welding under the truck and behind the lundette, so looking ttomake it bolt on.

Next few weeks ill be building on for my lmtv

Glad your ok, Ill be going with my m1078 and my buddy his bobbed m931. Headed out rt 80 around 1600

I have the follocomponentssale and may get a booth 1101 type flat deck trailer with ramps for sale with title, 12v and 7 pin connection set up 5 50% 365/80/r20 xzls I took off my deuce ($50 each) 4 mounted 11.00 goodyears 95% on 5 ton rims ($50ea) dibs called 5 5 ton split rims ($20ea) 3 sets...

1156 get amber and reds. Get the flat looking ones, the long ones barely fit under the marking light cover. They do not work terribly well as turn signals on the trucks but in my trailers they work fine.