• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Update: Had to replace the camera after the case broke. The replacement is working great. Now need a wireless camera for the trailer:
  2. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Fixed the electrical noise problem and the over-volt condition with a 4 ohm, 130 microhenry coil I made with 100 turns of 32 gauge magnet wire wound around a 3/4" x 3/4" tube form. There is still some screen distortion at idle but no noise. Guess it is a bit of voltage depression, pulling 20...
  3. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    No air conditioning at traffic lights. Yes, I pondered that. Far better to drive it electrically because the compressor will run at constant speed. In automotive systems driven off the crank, the change in performance from idle to cruise engine speeds can be great.
  4. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    FINALLY got the electrical system installed:mrgreen:. But I'm having issues with over-voltage, about 14.6 which is causing the video to drop out. Also, the picture quality is poor while running. So I used a 12 volt SLA battery to power it, this restored the quality and no drop out. So...
  5. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Got the camera mounted, high and above the center marker light. A little relief on the back of the light housing provided space to route the cable, then it follows the wire for the lights to the front of the box. There is a hole in the floor here for a radio rack, it then goes to the existing...
  6. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    After preliminary design of the electric compressor, I have settled on a frame of 10" square that is 21" long. This means it will live nicely on the passenger side frame rail. Plus it will have VERY SHORT electrical runs. And pretty short refrigerant line runs.
  7. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    I'm still on the fence about the evaporator unit. I found a 14k BTU/hour evaporator that will fit behind the seat. Could route air through ducts up the corners to registers. Or I could go with a small under dash unit angled up to allow transfer case to operate. I will make mockups of the...
  8. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Blue wire is accessory hot. So it will run with the ignition on ACC. Yes, documentation is lacking, for the price and made in China, what do you expect? At dusk, the IR illumination is good for about 50 feet. Which is more than adequate for blackout ops. The IR LEDs do give a faint red...
  9. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Postman dropped the package off today! I'm impressed, just appears to have some muted colors, not a real issue. I have yet to install, just tested inside. 18 feet of video extension wire seems adequate if using the holes under the seats. Tomorrow, the AC compressor should be arriving. I...
  10. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Yes, air conditioning draws power. Automotive air conditioning is far greater than most window units and rivals smaller central units. Hydraulic driven would work, only because the CUCV uses the power steering pump for brakes and steering, I'd rather not jeopardize that system. I thought of...
  11. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Right now, I've got about $100 in the AC project. Using an inverter was my initial idea but the space issue killed it. You need a dual hose unit, none are small enough. The electric motor is a gamble, I don't have a firm output graph and it is an orphan motor from surplus. Impressive 34...
  12. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    I'm converting the center red clearance lights to high mounted :mrgreen: center brake lights. Bringing the 1031 into the 21st century, eh? Right now, my focus is on air conditioning. Yeah, air conditioner. 28 volt, 3 HP electric motor driven compressor with aftermarket evaporator.
  13. Keith_J

    Bringing the M1031 into 21st century...backup cam and cupholders

    Way too cheap NOT to do. Although I would mount the camera a bit higher on mine. I'll be back after more credit card abuse :driver:. The camera is a MUST mod.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks