Search results

There is side to side structural framing but not as much end to end. I built the framing for the AC out of steel to connect the structural framing that runs from side to side to provide strength. The roof is strong enough to walk on, so I do not see any problem with installation the AC up there...

Thank you. I sold it before I finished the ceiling. I was going to use the same material that I did on the walls on the ceiling. I think another good option would be to use thin aluminum sheets and rivet them to the beams and then add trim.

Window Trim Finsihed. Finished a few more things during the last couple of weeks. The trim around all windows is now completed, new WEN generator is installed, and the front corner I finished installing the FRP panels from Lowes. Put the FRP on the side door, but need to finish the trim work...

Rory, Since I already painted the roof with the white rubberized coating last year, I decided to keep the white since it is noticeably cooler even in the Phoenix heat. So I guess I have the shoulder camo, but I do not think the US Military will use it again, unless some General wants new...

Thanks Rayzer and Camoyj7. With about four different coats of paint on this thing it was taking 60 grit sandpaper to even even out the chips. Still need to go back, and lower all the windows and mask it back off and paint anything where any tan is visable.

After 3 weekends of sanding, I finally have some camo applied to the outside of the trailer. Now just have to get all the information markings painted back on (tie-down, tire pressure, ect). In the process of getting the trailer ready for a car show at the end of October. Now that the outside is...

Ray, I was think 30 amp when I typed it, but did not make sure that is what I typed. Thanks. I have edited the original post with the correct info. I have already made the adapter for the front military plug, and now will just change out the end to the correct 30amp 125 female end.

AC Unit installed Made a little progress this weekend on the AC. Finished shimming up the brace so the roof section for the AC is higher do help with water drainage away from the AC unit. Also ran the flexible electrical conduit above the ceiling and installed 12 gauge wire to the WFCO Charger...

Thank you. Another use for the M915 :)

It does, but did not know if that would be the same as a civilian RV and if the distance to the back of the frame would be too long. Definitely will need to measure.

Csm Davis, You are absolutely right. I have been watching for one to do just what you are talking about to get parts. Seems like in Phoenix though, there are many RV recyclers/Salvage yards that want them just as much as me. There have been a few 30' 5th wheels for free that needed work. I...

Jakelc15 - I used Visio, but it could easily be done in word.I am still researching what others are using for Solar, and have read some long articles on the mistakes most solar panel installers make on RVs. I think I will by separate components instead of a kit. Probably go with a controller...

I agree Rayzer that these are a must for any RV build. The stand alone is also a great idea too. Thanks Rayzer for adding this additional information. It took me time to research all the options to figure out how to do these requirements to power both AC/DC.

I found this online for $129 on auction. Also www.pplmotorhomes.com sells them and has $9.99 S/H. The one I bought is 55 watts for the DC circuit. You have to by the Circuit breakers separately which are available from Home Depot.

WFCO- WF8955 Convertor/Charger arrived Received my WFCO-8955 Convertor Charge today. Looking forward to installing this and running all my AC/DC power through this and be able to power from Shore power/Generator power and solar power in the near future. This device also charges the battery from...

Great question LowTech. The large tube is for gravity water fill, and the other small one on the bottom is for a tank water drain. There will be a forth line on top for the vent, which connects to the gravity water fill housing in picture 3. The drain I will hook up to a spicket on the outside...

Trailer progress 8/16 Working on the Fresh water tank. Decided to put it in side the driver side storage compartment. Have to finish the drain and vent tube tomorrow. Also started to make the bracket for the Dometic 13,500 BTU AC unit to sit on the roof. The bracket will attach to the existing...

Rayzer, I think I may be able to use the hole saw maybe a few more times. But it sure good steel on those cross members. Once I get ready for the water heater, I may have some questions regarding the gas plumbing.

Camoyj7, I think I may do the fiberglass reinforced paneling from Lowes that I used on the walls for the ceiling. It is easy to work with, and secures to the plywood very well with the liquid nail. May then add some cross braces that are cosmetic, and I can use to support the fiberglass...

Here some photos of the main area of the trailer. I also like using the European style switches with the light in the top of the switch.