• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Latest activity

What's new

What's new New posts New profile posts Latest activity

BMI

Midwest Military Equipment

Eastern Surplus & Equipment Co

Members online

Total: 5,215 (members: 16, guests: 5,199)
  • peapvp
    peapvp reacted to mindshark's post in the thread MEP-803A Troubleshooting Question - RPMs cycle after warm up with Like Like.
    I'm a new MEP-803A owner - GOVPLANET auction - 2002, 2669 hours. Bottom Line Up Front (BLUF): I did extensive pre- First Start...
  • bajaman
    bajaman posted the thread 6.2 m1028 water pump in CUCV.
    Hello my water pump is leaking they say Oreilys has it new for 92 dlls Murray temperature pump control part CP5008 Any tips to change if...
  • 2
    2Pbfeet reacted to kloppk's post in the thread MEP 1030A with Like Like.
    There is no need to externally "flash" the gen head. THE DCS takes care of doing that automatically. Excerpt from the -10 operators...
  • jonesal
    jonesal replied to the thread M923 5ton horsepower gain.
    I see you've only heard crickets since this morning. Have you tried the search function focused towards this forum and the 5 ton...
  • M
    mindshark posted the thread MEP-803A Troubleshooting Question - RPMs cycle after warm up in Generators.
    I'm a new MEP-803A owner - GOVPLANET auction - 2002, 2669 hours. Bottom Line Up Front (BLUF): I did extensive pre- First Start...
  • jasonjc
    jasonjc reacted to Ray70's post in the thread RAPCOPARTSCOMPANY just joined our crew ! with Like Like.
    Welcome Aboard Rapco! I too have used quite a bit of the Gillespie paint for several generators, trailers and power plant refurb...
  • jasonjc
    jasonjc reacted to RapcoPartsCompany's post in the thread RAPCOPARTSCOMPANY just joined our crew ! with Like Like.
    Thank you @chucky for the warm welcome! I'm still trying to figure out how everything works on here, but I can't wait to interact with...
  • K
    kloppk replied to the thread MEP 1030A.
    Have you tested the Exciter Stator resistance to be sure it's good? TM says it should be about 12 ohms. Have you measured the DC...
  • Robert P
    Robert P replied to the thread MEP 1030A.
    Yes, everything i could find to test, tested good and found no issues with the wiring, connectors fuses, relays, it was those kind of...
  • K
    kloppk replied to the thread MEP 1030A.
    Have you performed the troubleshooting steps in the -24 TM for that fault? Results?
  • Robert P
    Robert P replied to the thread MEP 1030A.
    Ok thanks.. back to the drawing board for now lol
  • Robert P
    Robert P replied to the thread MEP 1030A.
    • 20250923_105701.jpg
  • K
    kloppk replied to the thread MEP 1030A.
    There is no need to externally "flash" the gen head. THE DCS takes care of doing that automatically. Excerpt from the -10 operators...
    • 1758651369725.png
    • 1758651585635.png
  • Robert P
    Robert P replied to the thread MEP 1030A.
    Hello. UPDATE.. so with all the help ive received i made progress, the Panel is active and the generator starts and sounds great, ive...
  • G
    grywitt reacted to 2Pbfeet's post in the thread Mep 831A load issues with Like Like.
    Using a dial gauge can be a bit fiddly until you get the hang of it, but if your cylinder is within .005mm (0.0002") that's great. The...
Show older items
114,254members
167,163threads
2,353,483posts
5,215online users
Top