• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Why do the Hydraulic Head clips fall off.

rustystud

Well-known member
9,071
2,387
113
Location
Woodinville, Washington
Someone here was asking why do the HH clips fall off ( I think it was David). I found out while reading the Manual (what a concept, reading the manual ! ) that the HH must match the injection pump body. There is a different spring located under the HH for different models of pumps. Now this is just one reason the clips can fall off. I'm sure there are many more reasons why they fail, but I'm sure this is one.
View attachment Scan0048.pdfView attachment Scan0049.pdfView attachment Scan0050.pdf
 

Floridianson

Well-known member
Steel Soldiers Supporter
7,390
2,434
113
Location
Interlachen Fl.
I don't know Rusty but I do have a plunger that has a coating on it. I will grab it today and take a pic. I believe this coating makes the plunger stick and then causes a gap between the tappet and plunger. Then when it unsticks the two slam together maybe causing a hammering affect that knocks off the retainer clip. My.02 anyway.
 

goldneagle

Well-known member
4,420
829
113
Location
Slidell, LA
How about just poor design... The engine in my truck does not even have a 1000 miles on it and the **** button popped off just from the truck sitting a few months without being run.
 

frank8003

In Memorial
In Memorial
6,426
4,973
113
Location
Ft. Lauderdale, Florida
How about just poor design... The engine in my truck does not even have a 1000 miles on it and the **** button popped off just from the truck sitting a few months without being run.
The tactical vehicle was designed for combat, endless fuel and **** be ****ed, forget the cost, lets do the conflict. The design encompasses the point of that there will be no tomorrow if She don't run.

It was designed to run to failure, once started She would not stop, How many hours, Nobody knows, but they all were designed to run and keep running.

Heck with the birds and bees
Run the truck a bit or else truck breaks
Time and money............... or run the truck.

OK, I like birds and bees stories,
but run the engine.
I am ready to be slammed.
 
Last edited:

rustystud

Well-known member
9,071
2,387
113
Location
Woodinville, Washington
I don't know Rusty but I do have a plunger that has a coating on it. I will grab it today and take a pic. I believe this coating makes the plunger stick and then causes a gap between the tappet and plunger. Then when it unsticks the two slam together maybe causing a hammering affect that knocks off the retainer clip. My.02 anyway.
If your running the 7 coil spring and the Hydraulic Head needs the 4 coil spring then your going to have trouble. Same thing if your running the 4 coil and need the 7 coil.
 

rustystud

Well-known member
9,071
2,387
113
Location
Woodinville, Washington
The tactical vehicle was designed for combat, endless fuel and **** be ****ed, forget the cost, lets do the conflict. The design encompasses the point of that there will be no tomorrow if She don't run.

It was designed to run to failure, once started She would not stop, How many hours, Nobody knows, but they all were designed to run and keep running.

Heck with the birds and bees
Run the truck a bit or else truck breaks
Time and money............... or run the truck.

OK, I like birds and bees stories,
but run the engine.
I am ready to be slammed.
Actually this was a tractor engine before becoming a motor vehicle engine so I don't think your theory applies here.
 

Floridianson

Well-known member
Steel Soldiers Supporter
7,390
2,434
113
Location
Interlachen Fl.
If your running the 7 coil spring and the Hydraulic Head needs the 4 coil spring then your going to have trouble. Same thing if your running the 4 coil and need the 7 coil.
I don't think people have been changing out there springs and tappets. If you did replace your head and took out a 90100A then put back in a 90100A then it should be correct. Here is the pic of the plunger and the discoloration. My collar even has problems sliding where it is. Think the crap fuel and not running the motors has the worst effect on the heads.
 

Attachments

Last edited:

Keith_J

Well-known member
3,657
1,313
113
Location
Schertz TX
I don't know Rusty but I do have a plunger that has a coating on it. I will grab it today and take a pic. I believe this coating makes the plunger stick and then causes a gap between the tappet and plunger. Then when it unsticks the two slam together maybe causing a hammering affect that knocks off the retainer clip. My.02 anyway.
Exactly. The return spring forcing the plunger to the cam lobe should always maintain contact, when the plunger floats is when bad things happen. And that happens with bad fuel, varnish on the plunger or other debris causing stiction. The plunger should always be free.

last missing clip incident had a nasty varnished plunger. This never happens to vehicles running fresh, clean diesel that are run at least once a week.
 

rustystud

Well-known member
9,071
2,387
113
Location
Woodinville, Washington
I don't think people have been changing out there springs and tappets. If you did replace your head and took out a 90100A then put back in a 90100A then it should be correct. Here is the pic of the plunger and the discoloration. My collar even has problems sliding where it is. Think the crap fuel and not running the motors has the worst effect on the heads.
How do we know what was in there in the first place ? Maybe some soldier replaced it with what was on the shelf at the time. Unless you take the time to check and see if your HH is matched to the injection pump you just don't know.
I'm only saying this is a possibility of a failure cause, NOT the failure cause for all Hydraulic Head buttons.
 

Floridianson

Well-known member
Steel Soldiers Supporter
7,390
2,434
113
Location
Interlachen Fl.
Yea you never know who what and if correct. I would still bet when it came to doing that deep of work it was someone that knew injection pumps. Was also put on the machine and spun up for testing. I am still finding fuel canisters not put together in the correct order.
 

orren

Active member
Steel Soldiers Supporter
240
25
28
Location
Live Oak, Florida, USA
James,

Now that you have the plunger out I would try and back-cut the slots for the retainer clip prongs so these prongs can be
bent-in past the vertical to keep retainer tight even if sticky.

I just received a new Chinese head and the retainer fell off in my hand when opening packaging.
Supplier is sending me new ones; we'll see.


Good luck,
Orren

I don't think people have been changing out there springs and tappets. If you did replace your head and took out a 90100A then put back in a 90100A then it should be correct. Here is the pic of the plunger and the discoloration. My collar even has problems sliding where it is. Think the crap fuel and not running the motors has the worst effect on the heads.
 

Floridianson

Well-known member
Steel Soldiers Supporter
7,390
2,434
113
Location
Interlachen Fl.
You can tell when a truck likes you it does not give you any problems. Are you guys talking nice to them once and a while.
 

rustystud

Well-known member
9,071
2,387
113
Location
Woodinville, Washington
You can tell when a truck likes you it does not give you any problems. Are you guys talking nice to them once and a while.
Floridianson is right. If the truck doesn't like you it will have all sorts of problems, but if you "sweet talk it" and tell it what a good truck it is then it will be happy and not break anything ! :) That's why our busses break constantly. The mechanics are swearing at them all the time ! Who likes to get cussed at ?
 
Last edited:
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks