• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

What have you done to your CUCV today/lately - Part 2

gottaluvit

gottaluvit

Active member
1,749
17
38
Location
Bethesda, OH (AKA: Flyover Country)
Another Ahab said:
Oh, I get it; thanks!

You all are one of those states that has all those orderly laid-out counties, whereas over here in Maryland and Virginia our counties all look more like they were laid out by somebody who'd been nipping a little too heavy from that "corn-in-a-bottle".
Click to expand...
Ours kind of look the same in the hilly section, but more layed out where the state gets flat.
 
CUCVLOVER

CUCVLOVER

Active member
2,352
9
38
Location
west Tennessee, just outside Milan
Another Ahab said:
Oh, I get it; thanks!

You all are one of those states that has all those orderly laid-out counties, whereas over here in Maryland and Virginia our counties all look more like they were laid out by somebody who'd been nipping a little too heavy from that "corn-in-a-bottle".
Click to expand...
Are you sure it was corn?
It might have been something else.
https://www.youtube.com/watch?v=io30s7-5VaQ

I didn't make the subtitles so don't blame me if its not good.
 
Last edited:
Another Ahab

Another Ahab

Well-known member
17,838
4,193
113
Location
Alexandria, VA
Another Ahab said:
Oh, I get it; thanks!

You all are one of those states that has all those orderly laid-out counties, whereas over here in Maryland and Virginia our counties all look more like they were laid out by somebody who'd been nipping a little too heavy from that "corn-in-a-bottle".
Click to expand...
gottaluvit said:
Ours kind of look the same in the hilly section, but more layed out where the state gets flat.
Click to expand...
That's IT; you're on the ball, gottaluvit; it's the mountains and hills (and water of course) that make the lay-out looney.

Now where the H*** were we before we drifted all the WAY over here. Time to get back!

The thread had something to do with the letter "C", but now it wasn't "Counties"......


county I.gif county III.gif
 
Last edited:
joshuak

joshuak

Active member
747
214
43
Location
Slower shore, DE
Another Ahab said:
That's IT; you're on the ball, gottaluvit; it's the mountains and hills (and water of course) that make the lay-out looney.
Click to expand...
There certainly are some sharp tacks on here.

Another Ahab said:
Now where the H*** were we before we drifted all the WAY over here. Time to get back!
Click to expand...
Gotcha Another Ahab, although thanks to you and gottaluvit for the pleasant detour.

It's not much, but here are a couple pictures showing new turn signal lens and break light lenses.


IMG_0730.jpgIMG_0729.jpg
 
cucvrus

cucvrus

Well-known member
11,290
9,683
113
Location
Jonestown Pennsylvania
cucvrus said:
I have a little tutorial on how to overhaul the CUCV pintle hook.View attachment 580454This is the broken spring off the M1009 Pintle hook. View attachment 580455View attachment 580456View attachment 580457I removed the jaw using a 3/4" socket and wrench. I cleaned the bolts and the holes were lubricated with nickel never seize. And I replacedView attachment 580458View attachment 580460View attachment 580461View attachment 580467 the spring with a hardware store expansion spring. Reassembled as good as new. nice strong spring and no need to beat the jaw open and closed. works like it was designed to 30 years ago. After a few coats of paint the hitch is ready to install on the Mule. I hope this is a helpful hint.
Click to expand...
001.jpgI had another customer stop by that saw this repair that I posted a week or so ago. I went to the hardware store and repaired his hitch for him. He uses it to tow hay wagons and it would not stay open and he needed both hands to hook up the wagon tongue. The spring was $1.75 very inexpensive fix. I just wanted to show you the spring in comparison to the old one.
 
Assel

Assel

Member
197
7
16
Location
Germany Schwarzwald-Baar
Since I drive my M1009 now almost daylie (way to construction site/quarry is just perfect for my CUCV, no Highway and about 25 miles one way + "fun" roads in the quarry) I noticed a coolant Leak, about 4-5 drops a day (visible on garage floor) so I crawled under it and found out I have a bad freeze plug, new set for the whole engine is on the way, also new radiator cap (old one has rust), new radiator hoses + new thermostat and some random gaskets (just to have things ready if needed)

Oh and I bought a needle scaler set for my compressor hrhrhr:grd: ... I really should think about buying a heater for my garage... Winter is CUCV work time for me :p
 
Another Ahab

Another Ahab

Well-known member
17,838
4,193
113
Location
Alexandria, VA
Assel said:
Oh and I bought a needle scaler set for my compressor hrhrhr ... I really should think about buying a heater for my garage... Winter is CUCV work time for me :p
Click to expand...
I got a brother-in-law living here in the D.C area who heats his house with a simple cast iron wood-stove.

His house is so warm in the Winters that he throws his windows open all the time.

If you got a source for wood, Assel, you might want to think about getting one of those. :smile:
 
Last edited:
cucvrus

cucvrus

Well-known member
11,290
9,683
113
Location
Jonestown Pennsylvania
I was pleasantly surprised to find out I could still buy and you can also new GM weather strips for the window channel runs on the front doors and the door to body door seals. These are not Chinese knockoffs. I am getting a few sets from the local GM dealer. I have been getting them for a 1991 V10 full size K5 Blazer Model. If that matters any I don't know. But they fit perfect and have the quality that I was used to getting in the past. Have any of you tried putting the LMC rear roof cab seals on the main body hull? Not even close to fitting. They bunch up at the turns and make a mess with weather strip adhesive. Oh well just thought I would mention the availability. Maybe if a few of us go out and buy some of these GM parts GM may make more. Or maybe we will just make them more money and they can clean out a warehouse somewhere. Either way new GM door seals and other seals for that application are the best you can get for your CUCV. Have a good a day.
 
You must log in or register to reply here.
108,530members
163,786threads
2,304,275posts
1,190online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks