- 2,052
- 56
- 48
- Location
- Milford / Michigan
Would this booster pump seal be in the injection pump gasket and o-ring kits that are available? I have a kit but I do not remember seeing the seal in the kit, but maybe it is/was?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Mechanical Booster Pump "making oil"
- Thread starter fordgasmz
- Start date
- 2,052
- 56
- 48
- Location
- Milford / Michigan
I checked my gasket kit and i did not have the seal in my kit. I just ordered the kit from SECO and it was $29 plus shipping. Price went up.
- 7,391
- 2,438
- 113
- Location
- Interlachen Fl.
That would be a toss up what would be faster and easer. Myself I would pull the IP and replace the seal in boost pump and oil to IP feed line.
Thanks for the write up though.
welldigger
Active member
- 2,602
- 15
- 38
- Location
- Benton LA
Actually in my case it turned out my ip needed rebuilt anyway. Governor weight broke off.
As far as what's faster. Swapping injector pumps is probably faster if you had one on hand or a local rebuilder. Is it cheaper? Absolutely not!
As far as what's faster. Swapping injector pumps is probably faster if you had one on hand or a local rebuilder. Is it cheaper? Absolutely not!
Last edited:
gimpyrobb
dumpsterlandingfromorbit!
- 27,785
- 747
- 113
- Location
- Cincy Ohio
Depends on if you watch GL real close or not.
- 3,021
- 221
- 63
- Location
- eldersburg maryland
i bought a genuine oil seal at the local injection shop for $6
- 2,052
- 56
- 48
- Location
- Milford / Michigan
Do you have the part number of the oil seal?
gimpyrobb
dumpsterlandingfromorbit!
- 27,785
- 747
- 113
- Location
- Cincy Ohio
Bumping this for Kasper31.
- 7,391
- 2,438
- 113
- Location
- Interlachen Fl.
Do believe you can also check for fuel in the IP by removing the rear most bottom plug out of the IP and see if it is draining out fuel.
- 2,052
- 56
- 48
- Location
- Milford / Michigan
I think if you pull that plug out and had the engine running, you would be draining your oil out too as it the oil pressure line would keep pumping oil to the injection pump.
- 7,391
- 2,438
- 113
- Location
- Interlachen Fl.
Yea got to do it with the engine shut down but the IP has a belly and believe you can check the boost pump for leaks with the intank running.
Stranger
Member
- 119
- 1
- 18
- Location
- Weatherford, OK
I was able to diagnose my MBP leak by running the in-tank pump.
This site is amazing! I was work through my diesel-oil problems using the guidance and information in this and another thread. You guys rock!
My in-tank pump was DOA, so I purchased one of the $50 surplus replacements on a certain web auction site. The new pump was amazing! LOTS of pressure. I found out after an hour drive that maybe it was TOO good because I had made two gallons of oil. I figured out that it was the FDC or the HH; no leaks from either. When I "removed" the two bolts securing the MBP and let it slip out of the housing a little ways diesel-oil mix started spilling out. When I turned on the in-tank pump fuel started pumping out.
[Sigh] Now I gotta figure out how to make space by jacking up the engine.
All for a little o-ring...
- 3,021
- 221
- 63
- Location
- eldersburg maryland
not an 'o' ring, it is a seal. remove the 2 front motor bolts and the LR mount bolt and push the front of the engine to the right, it will come out.
Stranger
Member
- 119
- 1
- 18
- Location
- Weatherford, OK
Okay. In previous comments it sounded like it was an o-ring seal. I haven't had a chance to take apart the MBP, so I have not idea what it looks like. Thanks for the heads up. I won't be looking for an o-ring.
I had no trouble getting the motor lifted and the MBP removed. Tomorrow I will order the repair kit.
Anyone happen to remember which TM describes disassembly of the MBP?
Last edited:
welldigger
Active member
- 2,602
- 15
- 38
- Location
- Benton LA
It's a double lip seal in the booster pump. The o rings are under the hydraulic head and around the fuel control rod.
Stranger
Member
- 119
- 1
- 18
- Location
- Weatherford, OK
It was in a TM I had never seen before.
TM9-2910-226-34
All your fuel supply pump repair needs are held therein.
TM9-2910-226-34
All your fuel supply pump repair needs are held therein.
Stranger
Member
- 119
- 1
- 18
- Location
- Weatherford, OK
The injector pump kit NSN 2910-00-489-5994 has gone up to $35 at http://secoaugusta.com/.
Stranger
Member
- 119
- 1
- 18
- Location
- Weatherford, OK
I thought mine was $35 shipped as well. But, then I got an invoice for $53 showing I was charged $18 shipping and handling.
Crap!
