Recent content by Shawn MacAnanny

I've had a couple made at Dennys driveshaft they are awesome and indestructible pretty much. Didnt have them made for the Deuce but for cars, but i dont see why they couldnt make one for you if you got the right measurements. Mi nitrous read steel driveshaft with lifetime warranty was only about...

Manual http://test.steelsoldiers.com/upload/M35/TM9-2520-246-34-1.pdf Page 214 shows rear output shaft seal size, and the following pages show the others all are 3.353-3.357" so they are the same seal Page 267 shows rear output shaft seal installaion just tap it in with punch Page 299 shows...

Manual http://test.steelsoldiers.com/upload/M35/TM9-2320-209-20P.pdf page 235 shows part #6 as the same parts though flipping through them i cannot find where it lists the actual part description these look like the dust shields not the actual seal which it does not show under figure 99, and i...

Hey guys i swapped in a new transfercase a month ago because of pieces i found. I decided to keep the truck just havent been driving it much and i need to swap the output shaft seal for sure, the input shaft seal i think was a little wet, the front axle seal hasnt started leaking but i figured i...

National indemnity had no problems insuring it. Most wont insure it with troops seats though, mine has no seats and it for cargo only

Is there anything special to replacing it? Just remove driveshaft, cotter pin and nut right? No need to count turns or use a puller to remove yoke right?

The bolt holes do have a bottom. i measured everything, and cut perpendicular slots on a pare bolt to make a thread chaser to make sure the threads were clean. I used an extra washer to make sure the bolts wouldnt bottom out, there should be about 1/4" in the bottom of the bolt hole extra space...

They were coarse thread in the case, fine thread on the stud. I didnt waste too much time with it, some studs came out whole, some the nuts came off with, i was using a 2ft 3/4" ratchet on the 4 i could get to with it and it took substantial force on them so im not sure i would have been able to...

I thought about it but they looked like fine thread, i wasnt sure where exactly i could get 5/8" fine thread nuts. Im glad i went with the bolts though, there is much more threaded in the transfer case now. Ive driven in about 20 miles at 55mph so far, i did notice a small leak on the output...

Gulfway didnt operate in DE but i believe they said it had to be kept in a garage or trailer too

I posted in the other thread the HUGE headaches i had with State Farm Commercial. I was insured, with historic plates, and unlimited driving and towing a trailer though. The just wrote the policy in the wrong state and i spent 3 weeks fighting a $1300 fine. They are awful. I switched to Geico...

Haha i dont have the time to ship it, i barely had the time to put mine in, they are very reasonable im sure I'd give them a call.

Yes they ship, they ship internationally too, the case i got was very nice, from Boyce they are like $1450, their mechanic went through all of them right there with me and made sure they worked, hooked air up, spun them all, looked inside them all, just so you know they wont come with the...

You can buy a brand new govt rebuild from TNJ Murray. That's where i just got mine last week. $800 for it plus shipping for you (im local). They had 9 left when i was there. I just swapped mine last night, took about 5 hours by myself with no impact gun. Then get the hoses/switch kit on Ebay...

Well i got it all done tonight, it was actually really easy. If i had been able to use my impact gun i would have been able to do it in half of the time, but right as i was starting my tow behind compressor/generator it decided to blow a fuse on one leg of the generator, then did it two more...