Search results

Anyone out ther have any burner racks and the grease catcher for an MKT? I need a couple of burner racks and a grease cather for my MKT. I am looking at having some made but I thought I'd do a quick check with the membership.

Well I went to get the MKT today at lunch. Woulda been maybe 15 minutes if it wasn't for that tire I mentioned in an earlier post!! All in all not too bad just a little time consuming and HOT!!! By the way thanks to all who replied in that earlier thread. I made a hose with a clip on air chuck...

Guys, I would like some suggestions or other opinions on the tire in the attached photo. It's on a trailer I am looking to pick up tomorrow. I won't be pulling it over about 15 or 20 miles. Well that's on the pull home, the pickup location is only a couple of miles from my work. It would be...

Anyone know offhand what size and thread the coolant sending unit is? For some reason I have 1/2" pipe in my head nut I don't have the truck handy to verify. I've searched but most post are about where it's located and how to test. Just wondering what the size is. Thanks!!

Bruce your inbox is full I couldn't send the pics.

Is there only one temp sending unit for the Deuce? I have seen several different temp guages and was wondering if the sending unit was like the oil pressure unit, one for a 0-60psi guage and one for a 0-120 psi guage? Mine has a 325 degree max guage and I have seen some with 250 or so max if I...

I have a noise in the front end/steering that I need some help with. I hear it usually when I am just getting started and am turning it at low speed in the yard. I hear a relatively loud clunk in the front end. It kinda reminds me of an old Jeep I have that the PO had put rear shackles on the...

Guys could any of you tell me what air pressure is "correct" for the deuce? I have searched the forum and found quite a few different opinions on air pressure settings. Anyone know what the "book" pressure is supposed to be or does it really matter as long as you don't go over around 120 psi...

Guys a while back someone asked about the availability of the fiberglass troopseat slats. I did a search and didn't see any responses to that post. Has anyone found a supplier of these? I picked up a set of seats that need new slats (Thanks jwaller!!!) and was wondering if anyone had found a...

Guys anyone have a set of troop seats near Columbia S.C. that they want to get rid of? I have the headache rack just need the sides with the seats on them. Also was wondering if anyone sells new axle vents for the Rockwells? Most of the sites I have looked at don't list vents among all the...

Guys I have a couple of questions I would like opinions on. The first is a gear oil leak on the front rear axle. I have some small spots of gear oil on the outer wheel on both sides of this axle. I checked it close and see no oil on the inside wheel or on the brake drums. From looking at it it...

At the risk of beating a dead horse, or stirring up a hornets nest I was wondering what the average wait time is for the SF97 to go thru?? I am at 72 days and counting and just was wondering if there is any light at the end of the tunnel, or is that the light from the oncoming train!!!!

Hey guys I was looking the other day for an air hose to set up to use with the gladhand on the back of the deuce. I was going for a 3/8 inch hose for a little more air volume. Well everything at the local stores had 3/8 hose but only 1/4 fittings. I finally went to the Grainger website and was...

Thought you guys might enjoy my new relief driver in action....

Guys I have a question. Whe I got my new Deuce home the other day I found about eight or nine brand new Govt padlocks all locked together in the toolbox. Any chance on finding a key for those puppies? I hate to toss them but they ain't much good without a key!!!!

Hello to all, just became the proud owner of a 67 Deuce. It's in incredibly good shape and runs strong. I have some photo's if someone can help me out with how to post them!! I have been checking out this site for a while but never thought I'd bite the bullet and get a Deuce!! I'm still not sure...