Search results

The wheel had a little play, the Army tech diddnt preload per the specs so I suspect the bearing is worn. ( never take someone else's work for granted)

Took the drivers side hub off to replace the bearings along with the seals, brakes,boots and any other thing I can. Question is, how do you get the races out of the hub? and how do you re set them? Everything looks ok except for a little water let in by a bad boot.

Thanks, will do. I did a search and found the info, then went to the garage looked the ip and saw the cover and I can tell that it was never messed with. will get a boost gauge and pyro meter tomarrow before I mess with fuel delivery. thanks for all your insite, it's worth more than money

Another question Where is the fuel delivery adjustment screw on the pump. I heard of turning the nut one flat at a time. It seems a little sluggish and I want to turn it up a little. Any pics?

Thanks I will give it a try, just a little concerned because my 2005 Ford 450's turbo blew again. 1st at 13870 miles and now at 41468 miles.

Been working out of town for a while and I just got back home to continue work on my deuce. Decided to degrease the engine to see where any leaks are. The engine was painted black by the govt over the top of the standard green.. Degreaser took off the black paint. Also degreased the top of the...

Never saddle a dead horse! I had a great friend who got killed by a crane block that had the clamps on the cable clamped the wrong way. Anyone who plans on using winches, or wrecker truck cranes for big lifts or pulls better learn proper rigging teqs or you can lose a friend or buystander.:cry:

Will do! Thanks

Thanks, I was looking at a coolant cab heater on a crane and I was thinking the inlet to the heater came from the waterpump. I will also put a can type engine heater on the line as well. I would get some pics of my project but my daughter still has my camera. Also, should I install cut...

I am putting a M151 heater in my Deuce and after working under the dash to route the wiring and making a bracket for the unit, now its time to run the hoses. Wanting to do the job right the first time, what hose should be the inlet for the heater? The one from the waterpump or the manifold? I...

What tm should I look in for installing a coolant heater, I just got a take out unit but no instructions

I changed the oil few weeks ago, no fuel smell or antifreeze in there. I have only put on @ 50 miles since coming from GL ( registration issues here in NY) Driving it , There hasnt been any exessive drainage out of the tube while driving. Oil level good with no smells. Not being used to these...

I noticed that mine has made a mess, but only after I let her idle for quite some time to warm her up to keep the batteries fresh here in NY in sub zero temps. Is this normal? I've read that too long of an idle will do this. Is this true? Also my tube looked like it was hooked up to the diff (...

Thanks JT, I figured out the door handle. I hammered down the tab that it turns against and it works fine now. I will dig into the window soon. I would bring it down but it is apart right now ( putting a new IP in) While I am at it I am going to install a M151 heater and a tank style engine...

I am in need of some heater parts for a project I have the heater Switch Resistor What I need is the mount, data plate and the other wiring It,s getting cold Any help? Thanks

Anybody have a driver side door laying @ in central NY? Mine just started to have problems with the outside handle ( wont unlatch but inside handle works? also when I roll down the window it wont roll back up. I would rather swap it out for another working one. I live in Utica ny

If you are willing to travel to NY, I could put you on my crew erecting a few buildings on FT Drum and I could teach you every aspect of welding you need to know in a month or so. Problem is that you will have to weld in the rain, snow, high wind, sleet 100ft in the air 10 hrs a day. All kidding...

Seal replacement I am going to start on a seal in the front and I was wondering , do you have to take it down all the way like this with zippered boots? and is the seal accessible with the knuckle still attached?

Yes it was leaking @ the boot and front seal. I mean pouring out under pressure. I would rather replace the MC than rebuild.

Thanks for your insite and help and great site as well. I am sure i will have more questions as I move along and when my daughter gets my camera back I will post some pics. OH! I allmost, I spoke with Sen Mccain last night ( helped on his campaign here in NY) and discussed in length the issue...