Search results

This one is either USAF CC Combat Controllers, (now TACP) attached to 9th HTMD, or one of the Fast Attack Bns' S-3 (Air) going by the UHF "shark fin" antenna. The Marines are smart, they have their own Air Wing, their own intrinsic Close Air Support CAS. Unlike the Marines, the Army has to...

Arming/Firing Box side of the the cable is a MS3106R14S-6S, 6 socket Connector Pinout: (This is from the HMMWV GMV 2x4 barrel LVOSS type cable) A=24VDC Positive B=24VDC Negative (I don't know what you should do for circuit surge protection) Edit: Dan In NM has the best idea so far, to use the...

If you go to the UPS Store or Mailboxes Etc they charge you out the arse because their lackey has to do the work. IF you go onto OfficeMax.com, click on Services, then Print & Copies. I uploaded the TM 9-2320-280-24P-1 Vol 1, then it gives me $542.85 ($550.83 if you want it 3 hole punched)...

My calculations for the rear is 14.5" wide x 46" long The fronts, 15.75" at the square front edge, 23.75" at the widest point where they bolt to the cargo bins, 55" long on the outside edge, 51.5" on the inside edge. Each car is going to need approximately 17ft of 24" wide 3/8" thick conveyor...

jshull said his mud flaps are 3/8" thick. My calculations for the rear is 14.5" wide x 46" long The fronts, 15.75" at the square front edge, 23.75" at the widest point where they bolt to the cargo bins, 55" long on the outside edge, 51.5" on the inside edge. Each car is going to need...

What's the thickness of the rubber used to make the mud fenders? This company has conveyer belt that might can be recycled into FAV fenders in 1/4", 3/8", 1/2" and thicker: Used Rubber Conveyor | repurposedMATERIALS (repurposedmaterialsinc.com)

I think the short answer is, there is evidence the MX-7777 was used on wheeled vehicles in some limited applications, not as a standard installation. So if you WANT to install one, to recreate a specific vehicle application or for operator convenience, then go ahead and do it. But it isn't a...

Do you have the GMV Bible yet? Special Forces Vehicle-Mounted Operations Tactics, Techniques, and Procedures ATP 3-18.14 (FM 3-05.214 September 2014 edition) Chapter 3 goes into details for the various accessories that makes a GMV, a GMV. September 2014 edition is available on Amazon of...

I know the hinges for the tool boxes are Ace ACE 5301833 Door Hinge 1/4" Radius I had to buy them for the bumper kit I bought from Ragman.

If anybody replicated the AM General 57K6230 Battery Cutoff Switch Kit, we worked withGreg at Dataplates.net to make the 3 instruction plates for the battery box exterior. The yellow on black battery wiring diagram plate that comes with the kit is the regular plate you see on most HMMWV that...

At least you have an original GMV radio sub shelf and kick guard.

The M1290 InfiniD Power Distribution Box/Inverter, I did the initial research on it quoted above. Inside the 9" x 11" x 3.25" aluminum box are two of these Vicor V1-P111-EV 24VDC to 12VDC 400 watt inverters inside: VICOR VI-P111-EVV DC-DC POWER CONVERTER 24 VOLT INPUT 400 WATT CHASSIS MOUNT...

M151A2 was 2nd military wheeled vehicle I drove. I recall both the RT-524/MT-1029 as VRC-12 and PRC-77/AM-2060 VRC-64 systems in use on the M113A2 based tracks, the MX-7777 right over the Driver's left shoulder, to switch off before starting the track, the big yellow and black decal on the...

The Student Handout you shared on Page 17, "Each FAV is scheduled for Periodic Maintenance (PM) by the Reynolds Electrical Engineering Co (REECo) Fleet Operations Department on a recurring annual basis, or 4000 miles (whichever comes first). The REECo personnel performing such maintenance will...

On G503 DDTrustee said the FAV mud skirts are made from some sort of rubber conveyer belt material (that is expensive). This company specializes in recycling/repurposing of industrial materiel including a large selection of multiple ply 1/4" to 1" thick conveyer belt rubber, in various widths...

I was asked about launching pre-rolled t-shirts during local Mardi Gras parades by a local Krewe displaced by Katrina. I don't want to gut out my original aluminum housings to fit a pressure valve, so a pattern for sand casting is in the works. Turret gunner will have boxes full of...

A clearer photo of the FT Lewis FAV Museum display, there are two mystery boxes to the right of the oil cooler: Is it possible they installed 2 batteries, wired the body/lights for 24v to power the MT-1029/VRC radio mount, and to allow commonality of the light bulbs with M-series parts, then...

24VDC VW components: The Bundeswehr VW Typ 181 aka "Thing" was rigged for 24VDC, to allow commonality with NATO and compatibility with radio communications equipment and slave starting/jump starting equipment. FAV, I'll have to find it again, there is a pic showing a possible 24VDC>12VDC...

Did you determine if your torsion bars being broken was the cause of your range of motion maxed out?

Is the VW ignition set up for 24VDC?