Search results

You need a torch to heat up the nuts , and a big breaker bar. Heat the nut as heat expands the metal enough to loosen them. I live about 80 miles from you would offer help but I will be in Dalton GA. for there annual car show swap meet at the fair grounds.. Good luck !!

Check your air filter, I bought a 85 m1009 the other day that ran rough at idle removed filter and that improved idle .. so I replaced filter much better now !!

Hello I am in need of a speedo gear ( goes in the transfer case ) for my M1009 Blazer ..PM me if you can get for me thanks JJ

Heater blower fuse I had bought a 1985 M1009 the other day and am currently trying to work out the Gremlins . Very helpful that I own another running ( 85 M1009 ). I noticed that Did not get gen 1 light on start up, but do get gen 2 light. and I got gen 1 light when I turned on heater...

What are the other two relays next to the starter (doghead) relay for?

Have any of you SS members had any luck at buying MV's from local state auctions. I was bidding on a 1985 M1009 the other day . long story short I lost it , sold for $665.00 I did preview it and was surprised to find it was all most rust free only it had a bad Transmission and rear seat was...

Doghead relay conversion completed Made a day of it did the doghead relay and 12 volt resistor bypass and AC 60 glowplugs , Now time to focus on a IP rebuild as I started smelling diesel fuel and found IP leaking and fuel coming down back side of engine block. Anybody else had this kind of...

Turbo for 6.5 Diesel Anybody needing a turbo for a 6.2 diesel , There is one listed on Atlanta craigslist Turbo for GMC Diesel--- 6.5 Lumpkin co GA is the complete set up off of a 1996 GMC... hope someone grabs this one ...

Flex plate & starter repair M1009 6.2 I was driving my Blazer to other day and went to the store, when I came back & went to start and got this loud grinding noise. I had had this problem years ago on a SBC starter and or flex plate problem. It finally started and when I got it home I...

Do not rush into buying the 1st one , do some research, This is one of the best sites available to you , check out other guys experience with bidding and picking up autos from GL sites . a lot of headaches . if you are not familiar with working on these vehicles it will cost a lot to find a...

M1009 Blazer $20.00 tag $100.00 ever 6 months insurance here in GA. listed as less than 1k miles per year.

There is a couple listings on ebay. for CDR Valves for 6.2 diesel cucv $44.00 & $49.00

I need a starter bracket for my M1009 Blazer also, so if anybody has some extras. Let us no thanks JJ

As I understand you can get the throttle shaft seal separately , would that not cure the leak and back flow problem . But Does make sense to just do the complete rebuild while you are in that deep all ready ..

Is there any way to research or trace the history of CUCVs as to there military Branch state or other tid bit's

I did not see the post date untill you sent your message , also thought i was replying to message not creating a new post have deleted post thanks JJ..

Sorry I did not see date on post , have deleted post did not no i was posting thought i was replying..

I have purchased the solenoid but yet to install it , I was concerned with the loud snap of solenoid . I came across a post here where a member said you could install a resistor to lessen the snap but did not remember the ohm value of resistor . If some one does no ohm value of resistor...

My Gauge quit working on my 85 M1009 , I tried to install a 12 volt gauge but when switch was turned on gauge would peg out so I removed it . I had read a SS post about replacing the ceramic resistor with a 300ohm resistor from Radio shack $1.27 for a pack of 5 150ohm I soldered two...

John Thanks for the fan shroud and oil cooling lines, I finally save up the $355.00 and bought a new radiator for my 1985 M1009 Blazer Got it running and now doing the oil and trans fluid and got to replace all rubber lines. but I think it will be worth it . thanks for the parts. N GA...