Search results

Findings ok guys, i tightened the alt belts per the manual (-20) and i load tested the front battery...it came up short and it says to replace it. i will do that for sure, but i was wondering what the procedure is for checking the alt output without the ice setup. i have a multimeter and have...

hi guys, new problem here. I am going down the road with my lights on and go to make a turn and my blinkers are going suuuuuuper slow. so i turn my lights off and try again and they run at full or almost full speed. I also noticed that the batt guage was going back and forth as the blinkers go...

hey guys, i picked up a 6707 tunable whip base and whip and I wanted to know what wire will i need to connect it to my civy cb radio. it's a standard cobra classic model. also, when hooking up that base, do i need to ground it? and what other wires will i need to connect to the base? sorry, but...

OH, and guys, what cables do you use to go from the adj. base to your cb? what cables am I going to have to hook up to the base, besides the one (coax??) that goes from the cb to the base.....sorry for being so lost, but this is my first time ever doing something like this....i appreciate the help!

man, you guys are great and thanks for the help thus far. I am starting the project now. I picked up a (6707?) tunable base and whip at the broadheadsville, pa show on friday. Also figured out on my own what wires go to where concerning those two BUS panels behind my passenger seat sidewall (one...

hey guys, a couple of quick questions that I have searched for and came up with nothing: 1. I would like to make the rear power bar that is behind the pass seat on the wall 12 volt so i can run a few electronic devices from it. what is the easiest way. right now, it is disconnected from the 24...

guys, do the rear brake drums crack on these? I have never had a drum brake vehicle before so I have no idea. When changing my rear brakes out, i notices these very little lines in the stopping surface of the drum that look like spots where the pads stopped and sat for a while. they hardly look...

hi guys, i just replaced my front and rear brakes on my m1009. first problem i found was my right rear brake shoes were soaked with grease. the wheel cylinder was not leaking and i am pretty sure it's the axle seal leaking. I was wondering if someone has a part number for that bad boy. i looked...

really??? i am not doubting you....i am wondering why no one else has chimed in. do the cheapie moroe's really give a decent ride on and off road?

hi guys, i have read dozens of threads and I am trying to figure out what you guys recommend for shocks. i dont want to spend 100 a shock but I'd like to get a good set. I only do some off roading and no rock crawling. i'd like to have a nice ride on the street as well..something that will help...

guys, can you tell me what you guys use for supply and return lines for m1009? if you only use oem...where can I get them? I have looked around and didn't see anything. my return lines and leaking and allowing fuel to return back...so i guess is loses prime and starts hard in the morning...

i looked in the troubleshooting of that manual, and didn't see anything about pulsing..... perhaps it was another manual. i appreciate any other help and advice you might have. thanks, pinwormfood.

can anyone tell me where they would start to find the air leak....is there a start to finish procedure for testing for them? perhaps a link?

i would love some pictures if you could....that would rock. thanks pinwormfood. pictures help me to identify things. i really don't have anyone that knows about autos that i can ask for help. it's very much appreciated. pinwormfood

just checking if this is the one. it says it's for crew cab, not m1009, not sure if they are the same....it was the only one i found on there. http://oem-surplus.com/gmwp/picpages/filterassy1725.html part number 12471725 any help would be great..... thanks, pinwormfood

Hi guys, I looked around in the forum and couldn't find a thread on this although I am sure there is one somewhere. Hopefully you guys can help. I park my truck on an incline at night, sloping down to the rear of the truck. when starting the truck this morning, it started, and then run for a few...

hey guys, just wondering if you can use the dimmer to "dim" l.e.d.s or are they only an "off/on" deal?

napa blades Jim1009, thank you very much for that help. I went and purchased the napa blades you mentioned. they have some big contraption bracket on them. what part gets snapped off, and I still dont see how they would work on the truck. maybe i have some screwed up wiper arm that doesn't...

Wiper blades Isn't a 18 inch blade too long? i know my 15 inch bade seems to go to the edge of the driver side left edge of the windshield....doesnt a longer blade start running into the rubber windshield gasket? thanks...pwf