Search results

So far I'm not impressed with Tech support and some parts of the kit. Anyone have any problems with the fitting that goes into the block for the turbo feed line. My fitting is bottoming out on the lower casting circle. And the feed for the fuel lift pump runs right where the exhaust from...

Is there a way to look at service records or any info like where it was used? or how many true miles it has?

I need new injectors all are shot so I was think 6.5 short because i will adventually get a turbo. What do you guys think of this kit? http://www.swdiesel.com/index.php?main_page=product_info&cPath=12&products_id=1302 Also how bad do you have to bend the lines to work?

I got my truck running today for the first time and It sounded like a gas motor spewing black smoke. The person helping me wants to start from scratch and set everything from top dead center. Right now I'm at my parents house and for some reason the manuals wont work for me. Can anyone help...

Anyone have a good or bad OEM one they want to sell?

I need a new starter, Should I buy a used one that "works fine" for a $100 buy one from a local starter shop not chines poo poo for $175 new one from OD roughly $300 I have never heard this truck run should also what would you guys do????

So are most Cucv's molested? I have 2 and it looks like both of them have been gone through. I can tell because there not factory screws where there should be and so on. When I go on government liquidation a lot of them look molested also.... Any horror stories?

first I wouild like to remind people Do not convert your CUCV to 12V . The 24V system works perfectly as is and is easy enough to work on. now thats out of the way, I'm trying to bring my m1008 back to OEM specs. The previous owner changed to 12v and said he did not change anything but the...

So a couple weeks ago I had some wires burn up on me. I changed some wires and everything looks good now, but my questions is why are there red wires that go to the 2 post terminal then change to blue last 3 inches? is that a fusable link? I tried reading the manuals but I get a little lost...

while trying to get my 24v alternator belt tight the bottom of the alternator in the case sparked then smoke came up from the right side of the 24-12v resistor. The wire that connects from the right side of the resister is fried. that wire goes to a 2 stud connector. Is that a fuesable link? I...

At idle how many hg's should the quage read? With a little fuel does pressure go up or down? Trying to chase down a late transmission shift Thank you dan

Ok so I bought my m1008 from a crack head pretty cheap, he told me that it ran out of fuel and that the system was changed to 12v. So I asked him what he did to complete the system? He tells me a electrician did it and just worked of the drivers alternator and put in i guess a relay to the...

So i took out all of the glow plugs to test them and one was broken about 3/4 of inch. So I take out the injector and i can look right down the prechamber and its no where to be found. the motor seems fine when it was running. do you think my motor ate it? if so what should I do?

ok Going to change the filter in my m1009. Im still a newbie and looked through the search and notthing could answer my question what is the best way to prime the filter? 1 So first I take out filter 2 replace with new one 3 open left valve 4 once fuel comes out close 5 crank...

Is the 205 that came in the m1028 and 1031 a fixed yoke or a slip yoke?

Can i run a 12v winch and a whelen 12v lightbar? I know some is 12v and some is 24v. would that be too much amperage for the 12v part?

Anyone have a good running cucv around ct? Im looking for a m1008 or m1028 or m1010. please let me know what you have