Search results

You might also find you want to go a more conventional air quick disconnect route. Such as a male disconnect on a ball valve off of the wet tank. This will allow you to use conventional airlines and fitting to run air tools if needed and to pressurize the system from an external source which...

Primer primer primer! Won’t start, push the primer. How does it feel? If you pump it rapidly, you can build 10 PSI of primary pressure with the primer. If it is properly maintaining prime, you should be immediately able to feel the resistance caused by the regulator when you press the primer...

Are you sure the primary fuel system is holding a prime? After it has set overnight, or a day or two, reach in under the cab and push the primer bulb with your hand until it is firm. If it has held its prime, it should be firm/high resistance from the first press on the bulb as the path...

I had no gymnastics whatsoever in Port Angeles just a few months ago. Took under 10 minutes with the EUC paperwork from the auction for my 1079.... It will get registered as a "commercial vehicle, not for commercial use" and a 4 wheeler will have a max 26,000 GAVW... Not sure if they uprate...

Was asked to start a separate discussion and a manual ctis drawing. we already had a thread on it so I revived that with a current diagram. it is also in my videos on youtube linked in this discussion. basically pin H is 24v. Pin R is control, pin B is inflate and pin C is deflate. You...

Or if you pick up a mouse along the way they may take the seat cover material for their nest... I found most of my drivers seat cover in the dash under the instrument panel when i got it home from the auction yard.

As long as you never make a mistake connecting batteries or jumpstarting, the PPD can remain bypassed. This could also be as simple as a bad connection at the PPD. Since it is out in the weather, it is not an uncommon occurrence...

Well at least it isn’t buried in the valley like on a PowerStroke:)

Should be a twisting lock, I have one in my basement. less than a 1/4 turn counter clockwise to unlock, then pull straight off… As mentioned the red sw is a remote battery disconnect, same as the one under the cab on the pax side with the remote ign and start switches…

Is that the original green shaft tube? Can you measure the wall thickness with a vernier calliper?

Ether in itself is not a problem, it is just a clean gaseous more easily combustible fuel on top of the fuel that is already being injected. it is when it is overused and the full length of the intake plumbing is filled with it, that you have the over-revving/damaging runaways that do harm. an...

yep, knock out the freeze-plug and put in a 1500W heater. 15-30 minutes of preheat and it will start like it is 70 out:)

inboard of the air filter. usually a red cannister on top of a solenoid valve(oriented vertically)..

And tha And that reservoir seal ring is important as the reservoir must be sealed enough to pull enough vacuum to draw make-up fluid from the main AOP reservoir…

Pretty easy to make any truck manual to demonstrate. The last two of Dave Andersons roundups I went to, I brought a little switch box that has my dead controllers cannon plug and one momentary double throw toggle switch installed. I could plug into anyones CTIS harness And manually control the...

Does it have fluid? Allen head Filler plug, outboard rear corner. They are pretty simple and quite robust, usually if they have fluid they work(trying to think if I have encountered anyone with a bad one, its usually something else)… quick test, select suspension raise or...

Hand pump not working?

it takes hydraulic fluid to hold it up, and at only 6" up, it should come down all by itself via gravity, unless it has somehow tripped the safety check valve in the cab cylinder base. Did it appear to bounce when it locked up? This may have been possible if you were low on fluid and pumping...

At the very least stem Oring seals, and wheel Orings. Expect every rubber seal on this truck is bad, and you will probably be mostly correct:) you can get all the lift arch hucks with a cutoff wheel, I did:) i chose rail on rail with captured “springs”(hydraulics) for my habitat and am...

Well, if you unplug the controller, that will disable the system. With the tires aired up and the controller unplugged the tires/wheel valves should hold air. You can confirm this 2 ways. 1. The CTIS dump valve over the rear axle and the front CTIS dump valve beside the transmission(passenger...