Search results

Doing a bunch of wiring under my hood and dash. Have the two extra fuse boxes in, one under the hood, one inside. The one inside controls the switches to the relays powered off the one under the hood. The one inside is powered off a relay that is fused out of the engine compartment box, and...

I've mounted the plates, and put a light over the rear. Will this pass NYS inspection?

I'd like to lose the blackout lighting system.. The lights I'd like to change to 12 volt and use for running lights. The switches I'd like to just remove. Then I'd like to have the headlights work like a civvy truck. Also, can I just remove the data testing port and tuck the terminal up...

I have a whole slave cable set-up, out of my cucv. From the cap back to the end lug of the cables. I also have both antennae mounts. Lastly I have the spare tire mount, just not out yet. I would like to find another front blackout light, to put where the slave cable hookup was. I want to...

Having needed a part now, I wonder if we could have another wiki at the top, for "parts I have, willing to part with...". What do you think?

My speedometer needle swings below zero at rest. Is there a pin that should be there, and if so can I place a new on there? If it's not repairable and no longer accurate, I have access to a used gauge cluster out of a civvy truck. Can I swap just the speedometer into mine? I remember having...

I need a front drive shaft for a M1009. Anyone have one, or know what swaps?

Bought a lug crimper and some hum-vee battery clamps. Now I need to find some good battery / welding cable. Anyone know of a good source for some and lugs to fit?

Man I hope it starts. Also bought some of those cheap cup holders, and a lighter socket. Just gotta get a fuse box, interior light, some body panels, seat belts, ...

Finally got the "new" key switch into the blazer. Now I have the wait light, a GEN 2 light and a clicking noise when I try to turn it over. The batteries were taken out, put on a charger and read as fully charged. They also showed over 13 volts each. Is it possible their still bad. They...

I know this has all been covered before, some of it numerous times, but please bear with me. 1. What glowplugs for a manual conversion, no controller card or anything except a switch, a relay, and the plugs? AC60's or Wellman 070's? 2. What size freeze plug heater? 3. Where to find a gas fueled...

Having gotten my cucv I find myself needing repair panels. Basically the drivers side bottom, from front to rear. Is there a source that is better than another.

The price seems right on the rebuilt gear reduction 12v starters. Anyone using, or used one? What do / did you think.

Wondering if I can place a 9nth glowplug inside a steel pipe, with a glass window, facing out of the dash, to indicate how hot the other 8 are? This is similar to the resistor wire used on my tractor as an indication of it's readiness to start.

Re. my M1009 6.2L diesel, Does anyone know the battery configuration for the cucv's? What post where? As these are built on a small block configuration, will small block exhaust manifolds fit? How about freeze plug heaters, are they the same as a small block? I see people are swapping in...

1. Where are the battery terminals located on a cucv? Are they post or screw, top or front, positive on the left or right? 2. What glow plugs to put in to make it a manual button glow plug system like in the stickies?, my tractor runs like this, and it's fine for me. 3. I'd like to have one...

Up at Ft. Drum, event 3609 invoice 384465 Total Amount Charged: $2,490.21 Resending another EUC with a export letter and lisence copy out today. As I would like to get this on the road as quick as possible, what else should I do, and where do I get a key? Thanks all.