Search results

Seen this the other day what is it ? what is it worth not running ?

How often do the multi fuel engines have cam shafts that fail. what is the common engine failure for the multi ?

i am looking to r/r my clutch. i was reading the SS site and i found this post but i cant find the TM The TM are in the TM section. They give all the cleaning and inspection for the clutch. Gives step by step for remove and install. Every thing you need to know. Look for TM 9-2320-361-34...

I took the day to pull my trans apart on the bench. and found a crack in the 2nd , 3rd gear that sits inside the syncro anyone have a junk trans i can get the front shaft from as a centering tool? also looking for a top gear shaft.. has anyone had a syncro out and apart ? My 2,3 shifts in...

Trans is stuck in the location of 2nd but not driving at all as if the clutch is in any ideas I'm bushed now from pulling it back home with a pickup truck. But I'd like to dig in when i get the steam back after lunch maybe I cant move the shifter at all. clutch goes in an out as if its ok...

I was driving in the deuce today and i started to shift into 3rd when it was very hard and did not feel like it went in. it does drive in 3rd sometimes goes in easy other times not wanting to go fully in I get drive in no slipping well 2nd is slipping a little anyone in the flint or mid Mich...

Hay M109a3 guys few questions 1 what is the plug on the box body behind the cab it has 2 wires plugged on a terminal that is bolted out side the box near the bottom pass side 2 fan and fan box there is a box on the wall that said fan control 24v i guess from where 3 is there a wire from...

If you plan to attend the Mega car and MV show please contact me I'm planning to give a gift to All MV drivers I need to know who is planning to show up as we can get your gifts ready in advance. thank you very much . I hope to have venders someday soon September...

September 27, Mega Classic Diner Cruise, Corunna Road near Linden Road, Flint, 3 - 6PM this is the correct copy and paste from the ad after it was dont...

hay guys in Michigan , is there someone that could have a stop by and check out a deuce with me ? M109 71 flint Mi thanks

ok i have soaped every thing down. and this regulator looking thing is hissing 1. What is it ? .. 2 Is there a screw that would go in the side of it ? " air is leaking from the 8th inch round hole any other input welcome maybe i have this all wrong

If anyone might have fuel strainer. I need one on the cheep that is good mine is missing the screen . also is there a work around for the sliders on the black out sheets on a M109a3 also need about 4 sets glass , black out sheets and slides and window hardware maybe someone has worked...

I have automated industrial printing gear , what would be your top TM picks to have printed for the Deuce and why i can make 1 1500 page book in about 30 min

I have found that i can not print some of the PDF's on the site like the Deuce Axle paper with the photo my photo steps ..... i have researched and found that some PDF files must have a permission set for printing in the security of the PDF by the maker of the file . has anyone had...

who do you call , what do you do , when she just stops making them nice diesel sounds . what is your recovery plan when your not in you neck of the woods as well all seem to drive the trucks all over from state to state or across the state to shows and advents i wonder if my AAA towing plan...

this is a update for Sept. 27,, 5 - 8 PM for show on M21 1 mile west of I75 the last post said 3 - 6 that is a mis print the show is 5pm till 8pm or later with D J bob steele oldies and classic rock if you would like to have a swap table its all on you bring your own table NO charge ...

Hello I have been looking all over the truck and i dont see a fuse bus or any fuse block / box on the cab in the motor area are 3 boxes in the M109 box on the back , So is there a fuse block ? like a standard auto ? also what is the feed for the M109 box for lights inside ? thx I have...

The owner of the Mega 50's restaurant in flint has been having car shows. after i drive my M109a3 and had a very good review with my truck there he ask asked if the SS guys would like to come for a show in Sept. if there is any interest please reply soon the location it M21 and Linden...

Any one in Michigan know of Labor Day things going on other then Det. OR any other advents coming up in Michigan

I need a fnt window for M35 or glass has anyone used plexy or lexan if i spelled them right also I need a set of slides for the M109a3 van windows + black out sheets and other window hardware like arms on the VAN body 's window or would like to buy one PM Me also