• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. muthkw25

    My m925a1 build "Brutus"

    Installed a 6" donaldson snorkel and cut 6" off the intake tube. Didn't want the snorkel 2 ft above the spare tire mount. After hard top goes on I will push down a little farther to get it as close to the hardtop to blend in.
  2. muthkw25

    My m925a1 build "Brutus"

    My buddy helped me with the dual fuel line mod. Noticed some more improvement in performance but drastic change. Decided to add some armor lights and replace the halogen bulb with a LED replacement. It's a PAR36 bulb. They are used for landing aircraft. Very very bright. Have them wired...
  3. muthkw25

    My m925a1 build "Brutus"

    I decided it was time to put a Pyro in before doing any significant driving or performance mods. Truck barely gets to 900 degrees pulling hills. Exhaust is clean when warmed up and pulls great. No plan to swap any buttons out. Plan on leaving it as is. As I looked at truck more, the radiator...
  4. muthkw25

    My m925a1 build "Brutus"

    Purchased tmg air filter and wire basket for less restriction. Changed engine oil and filter. I also decided it was time to change the muffler. I was looking for a different exhaust tone and went with a 14" body 7" diameter magnaflow stainless muffler. It's small enough to hide completely...
  5. muthkw25

    My m925a1 build "Brutus"

    Purchase a strainer and had a portable sand blasters come out and work on the bed. Inside of bed had the worst rust. Took longer to setup then it did to do the job. I primed it with 2 coats and sprayed herculiner on surface with 2 gallons to seal the bed surface.
  6. muthkw25

    My m925a1 build "Brutus"

    I decided to take the plunge and enter the 5 ton world. Had m35a2s and variants for 10 years and wanted a 5 ton. Came across a nice m925a1 back months ago and decided to start a new build. His name is Brutus. Truck came with all led lights minus front side markers and spin on oil filter...
  7. muthkw25

    My first multifuel?

    Amazing resto. Very meticulous.
  8. muthkw25

    Turbo for NHC250 Cummins?

    My buddy turboed his m925a1 and use a hx60 turbo with a mrap intercooler and radiator. Lifted the cab and hood 2 inches. He also installed a methanol injection kit. He had his pump build by premco and had a #20 button installed and also 20% over injectors by premco. I can tell you from first...
  9. muthkw25

    Steel Soldiers MV of the month 2023 - September VOTE HERE!

    Thank you everyone! Much appreciated by all those who voted.
  10. muthkw25

    10 Ton M123 A1C & 10 Ton M123 E2 Rescue

    following this resto.
  11. muthkw25

    MV of the Month September 2023

    My 1971 M35a2 with winch
  12. muthkw25

    M818 gets a 7(6+1)-Speed

    Awesome build!
  13. muthkw25

    My 1971 Am General m109a3 RV build

    Today marks the end of my build on Smokey. A fellow steel soldiers member purchased the truck from Alabama and will be taking off where I left my build. Genuine good people and I am excited to see where the build goes. I have had a lot of great memories with the truck and I shed a tear...
  14. muthkw25

    M109a3 rear door lock

    My dad and I cut the padlock off mine and installed a deadbolt lock and bolted a piece of steel to the metal rod inside the box. Very simple and easy.
  15. muthkw25

    Oil pressure gauge and sending unit issues

    Yes and it did not work at all.
  16. muthkw25

    Oil pressure gauge and sending unit issues

    I ran a separate ground wire from the gauge to the firewall and it's not working. Gauge is getting 24v. And 24v is leaving the gauge and the wire going from gauge to sender is new. Not sure what else could be wrong but the sender because none of the other gauges are malfunctioning. Just an odd...
  17. muthkw25

    Oil pressure gauge and sending unit issues

    My old oil pressure gauge stopped working. Installed a new gauge and still nothing changed. I have 24v going through line 27 and 24v leaving the gauge to head to line 36 to the sending unit. Ran a new wire to the old sending unit and nothing changed. Installed a new sending unit now and the...
  18. muthkw25

    M1061a1 restoration

    Today I moved my dads ford compact diesel tractor on the m1061a1 back home. Drove great behind the truck. Truck did great at 50 mph. Trailer has had alot of use since finishing it.
  19. muthkw25

    M1061a1 restoration

    I have also thought of this plan. Originally looked at a s280 but I'm now really considering putting my s250 on it and using that for sleeping in and then the rest of the space as a deck for my girlfriends and mine m274a2 mule to strap down for camping and shows and then when the mules not on...
Top