Search results

I have 2 hunter 35k heaters at Warner Robins I was hoping someone could pick them up and store them until I can get someone down that way to pick them up. Its 2 of these I think they weigh around 60 pounds each. I am willing to pay gas and a few bucks. Thanks, Will will@pawnking.com

I won this contraption it is an STE ICE diagnostic set. I think it is for the FMTV's but not 100 percent sure. It has a PC interface box but no PC. Does anyone know anything about this set. Thanks Will

I won a rolling compressor at Warner Robbins but my hauler is sick and is out of commission for a few weeks. I was wondering if anyone would be willing to pick this compressor up for me. I am willing to pay for fuel and a few bucks for your time. When my friend is better he will come pick it up...

I have a mep-814a generator. I am having some trouble with the fuel system. It has a primer pump just below the IP. There are 2 bleeder bolts on the IP. I can crack them open and prime the pump it will draw fuel and then start but die a few moments later and have lost prime or sucked air. I know...

I have a few Allison transmissions. They were intended for Oshkosh Hemtt use. They have a 24 bolt bell housing with approx 21 inch diameter pattern. Some are stamped HT740 and some are stamped HT740D. Both types have the same part number 23014539. The crates are all stamped with nsn...

I smoked an alternator in one of my M923A2's. I was using the truck to slave one of the MEP-952B gens for a while then the next day this happened. It really cooked up.

I recently won a mep-925b gen. I have been reading the TM and searching the net for more info. The TM lists the spin on oil filter as 541.050.2E, I looked up the filter for a generic Farymann 43F which is listed as a HW1103. Does anyone know if there is an off the shelf Napa cross reference for...

I won a lot of parts at FT Benning GA. I bid low because I wanted the set if mirrors and I won. Here is the auction: http://www.govliquidation.com/auction/view?auctionId=7052287 If someone local in GA would pick it up we could split the stuff. I want the mirrors I don't know what else is in...

I have a new-to-me mep004a generator. I changed all the filters and fluids, they were all drained anyways. It fires right up and runs smooth. I can adjust the frequency with the manual throttle control but the frequency adjustment knob below the freq meter doesnt seem to do anything. In the TM...

I bought an M85-200 laundry trailer. It is an XM1061E1 trailer with the laundry unit built on top of it. There is a data pirate for the trailer and another for the entire unit. I am planning on taking it apart so I can use the trailer so I want to use the information from the trailer plate for...

My alternator/generator went bad and was making 30+ volts and blew my abs ecu. I replaced the alternator and then the ecu and all is good. I opened the old ecu to see what was going on in there. There is a protection diode in the module it is a 5KP33CA. This type of diode is designed to protect...

I am pulling a 6cta8.3 motor from a m923a2. I am going to pull the hood and radiator then start at it. I was going to pull the trans with the motor. Does anyone have any pointers for me or anything I should beware of. Im sure a few guys out there have pulled them before just not me. Any advice...

Truck pull Orange Country Fair Orange CT 9/20/13 There is a truck sled pull at the Orange Country Fair Friday 9/20/13. I spoke with the guy in charge he said it was fine to bring down military trucks they are a little bigger than the weight classes there but he said we could pull them and have...

I have found an inexpensive substitute for the Allison reverse pressure switch (which Allison charges 135 dollars for). The part is 416372C1. It is used as a reverse switch in International trucks and I believe on HETs and other larger military tractors. It has 2 terminals on the back, you can...

On the center of the timing cover on an NHC250 is a camshaft cover plate. There is an o-ring seal it says part of kit 3011472 in the tm. The diagram shows the cover then 2 shims and then the seal. I am getting some oil seeping from this cover. I called cummins support they werent able to pull...

I searched the forum but could not find what I was looking for. My 931a2 air compressor is getting weak its fine when driving but wont build enough pressure at idle. There are no leaks the tanks hold air overnight. I was wondering if anyone had part numbers for the compressor or if there is a...

I have an H140 heater on a pallet its around 320 pounds. I had a few shippers lined up to pick it up for me but none of them want to deal with going onto base. They call and the office there gives them a hard time. Can I pay someone to pick it up for me and I can have my shipper come get it off...

I recently won a m923a1 and it was delivered today. I took it for a spin it has some good grunt to it. When turning it feels like it has lockers. It has the pto and fording kit but no winch. It was rebuilt and the data plates were replaced so at one time it could have had the locker info plate...

Is there a difference between the military water pump and the cummins oem pump. The military one has side edges on the pulley and the oem one has a flat pulley no edges. Are they interchangeable? Thanks Will

I am looking for input on which states GL will send you a title instead of the SF-97 form. I believe some states wont accept it so buyers in these states get a title. Can anyone chime in on this? Thanks Will