Search results

OK. Lets regroup here for a moment. You have replaced the points and condenser, checked the electrical system for spark leaks and are now checking the fuel system. You replaced the fuel filter and rebuilt the carburetor. When you rebuilt the carburetor did you replace the governor diaphragm and...

Was the large Torus nut loose ? Looks like something went through the vanes like a crank flywheel bolt or the Torus nut. Can you verify if the input shaft has the "steel bushing" on it ? I cannot tell from your picture.

OK. First off you need to determine if your ignition system is working properly. That means your points, condenser, cap and rotor, spark plugs and cables. Once they have been fully checked out, you then can go and check the fuel system. No more jumping around. That gets you nowhere fast. You...

I have a spare carburetor I can take pictures of as I tear it down to show you how to rebuild it. Will that help you ?

You say you rebuilt the carb ? That opens up a whole new can of worms. Did you replace the "piston" thingy (accelerator pump) that squirts fuel into the manifold ? There is usually a small check valve at the bottom of the bore (ball bearing usually) . Also you mention the idle adjusting screws...

Agree !

Are you saying you have 24volts going to the points and condenser ?

deleted

Put in the new points and condenser. Then let us know how it runs.

Agree with "williamh" about the condenser. When I was a young man all gasoline vehicles had "points and condensers" . No such thing as HEI or any electronic ignition. One major "give away" in your statement was the engine would fire back up after stopping. The condensers job is to "absorb" the...

Well I finally finished tearing down all the HydraMatic transmissions. I took a picture of all the cases and parts I had to throw away. Really sad to look at.

Yes. This problem can be real serious. Hopefully adjusting the "modulator" will fix it. If not than you will need to get back into the transmission. Sadly, a lot of repair shops do not change out all the seals in a rebuild. I never used the "nylon" seals in a TH400. They were never meant to be...

There is an adjustment on the "Modulator" . Take off the vacuum line and you will see a small "straight" slot for a screwdriver. Turn this in or out to fine tune your shift point. The modulator is the transmissions way of knowing how much throttle you're using. So if your pressing down hard on...

Got another question today about the front and rear clutch pack plates. I guess I never answered it, something else I forgot. Anyway, there was two types of steel plates and two types of fiber plates. Waved and flat. The wave plates came from the civilian market and where initially used in the...

I was asked a question today about where I get my "new" clutch plates from. The answer is from private collections. "Fatsco" still has some "fiber" plates around but they want almost $10.00 a plate. They cannot get new fiber or steel plates either. So when their stock is gone, it's gone. I have...

Well I did it again !!!! I had the machine shop make-up some throttle valve shafts so I could replace all those bent ones, but I didn't ask for a quote. Again ! I didn't think having 20 small shafts made would cost so much. WRONG !!! Here's what $1002.00 will get you. The wife wasn't too happy...

I have good days and bad days. That post was a bad day. Though it has been getting harder trying to keep a positive attitude about these old 303M HydraMatics. Now with the "border" issues with Canada I don't even know if I will be able to see "plowboy" in Edmonton this June. Really pissing me...

I was a commercial welder for 10 years. During that time I welded "steel", "aluminum" , "stainless steel" , and cast-iron" . The cast-iron was the worst. One of the major problems is that cast-iron is very porous. That is especially important when welding cast-iron that has absorbed oils like...

Here's some information for people needing to check their pressures in the 303M. Hope this helps "Blake" .

This is just a "general" wake-up call to everyone in the military vehicle community. Our parts are old and getting older. Cast Iron in particular becomes more brittle with age. Today after spending hours cleaning a bellhousing, I found a major crack in the flange. I couldn't see it until all the...